BenQ LW61ST Display menu Picture menu Function Description Teaching, Template, Picture Mode, Tint

Page 43

1. DISPLAY menu

2. PICTURE menu

Function

Description

 

Teaching

Provides several preset patterns for various teaching purposes.

 

Choose Blackboard or Whiteboard first by pressing /

and

Template

press / to choose the pattern you need. Press MODE/ENTER

 

to display the selected pattern.

 

 

 

Picture Mode

Pre-defined picture modes are provided so you can optimize your

projector image set-up to suit your program type. See "Selecting a

 

picture mode" on page 30 for details.

 

Reference

Selects a picture mode that best suits your need for the image quality

and further fine-tune the image based on the selections listed on the

Mode

same page below. See "Setting the User 1/User 2 mode" on page 30

 

for details.

 

Brightness

Adjusts the brightness of the image. See "Adjusting Brightness" on

page 31 for details.

 

 

 

Contrast

Adjusts the degree of difference between dark and light in the image.

See "Adjusting Contrast" on page 31 for details.

 

 

 

 

Adjusts the color saturation level -- the amount of each color in a

Color

video image. See "Adjusting Color" on page 31 for details.

 

This function is only available when a Video, S-Video or Component Video

 

 

signal is selected.

 

 

Adjusts the red and green color tones of the image. See "Adjusting

Tint

Tint" on page 31 for details.

 

This function is only available when a Video or S-Video signal is selected and

 

 

the system format is NTSC.

 

 

Adjusts the image to make it look sharper or softer. See "Adjusting

Sharpness

Sharpness" on page 31 for details.

 

This function is only available when a Video, S-Video or Component Video

 

 

signal is selected.

 

Brilliant Color

See "Adjusting Brilliant Color" on page 31 for details.

 

 

 

Color

There are four color temperature settings available. See "Selecting a

Temperature

color temperature" on page 31 for details.

 

 

 

 

3D Color

See "3D Color Management" on page 32 for details.

 

Management

 

 

 

 

 

 

Save Settings

Saves the settings made for User 1 or User 2 mode.

 

 

 

 

Operation 43

Image 43
Contents LX60ST/LW61ST Table of contents Safety Instructions Important safety instructions3000 m Feet This apparatus must be earthed Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions Keystone/Arrow buttons / Up Down Remote controlNetwork Setting Enters network setting directly Test Source selection buttons COMPUTER-1, COMPUTER-2Numeric buttons VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer MIC/VOL +Replacing the remote control batteries Remote control effective rangeOperating the projector from Front Rear Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsLW61ST Connection ConnectionConnecting audio Connecting video source devicesPlaying sound through the projector Device About the microphone inputStarting up the projector OperationFine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Highlight Using the menusHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeAdjusting Brilliant Color Fine-tuning the image quality in user modes3D Color Management Selection Description Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right Hiding the image To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeTo view your pictures as a slide show, follow these steps When viewing thumbnailsPresenting from a USB Reader Supported image formatsShutting down the projector Direct power offSetting Press Power or OFF a second time. The Power indicator lightBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced DNS Server Wired LAN Subnet MaskDefault Gateway IP AddressDescription of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save SettingsSearch System Setup Basic Function Description Quick AutoTimer SettingsLock AdjustmentsReceiver Panel KeyClosed System Setup Advanced menu Function DescriptionBaud Rate Test PatternSystem Reset AllNetwork CurrentCare of the projector MaintenanceExtending light source life Setting Light Source Mode Selection as EconomicLight source information Getting to know the light source hourReplacing the light source Timing of replacing the light sourceStatus Message Light Status & Description Power events IndicatorsThermal events Troubleshooting Projector specifications SpecificationsWall mount installation DimensionsMinimum installation requirements Wxga Ceiling mount screw Minimum Ceiling Height mm = f + H + b + 60 + 274+ cSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Disclaimer Warranty and Copyright informationLimited warranty Copyright