Wayne-Dalton 9800 installation instructions Vertical Track, Stacking Sections

Page 15

7

Vertical Track

 

Tools Needed:

IMPORTANT: The tops of the

3/16” Drill Bit

vertical tracks must be level

 

from side to side. If the bottom

Power Drill

section was shimmed to level it.

7/16” Socket

The vertical track on the shimmed

side, must be raised the height of

Driver

the shim.

Tape Measure

Position the left hand vertical track

 

Level

assembly over the rollers of the bottom

section. Make sure the counterbalance

 

 

cable is located between the rollers and

 

the door jamb. Drill 3/16” pilot holes for

 

the lag screws. Loosely fasten jamb

 

brackets and flagangles to the jamb

CABLE

fLAGANGLE

DRUM

 

5/16” x 1-5/8”

 

LAG SCREWS

 

VERTICAL

 

TRACK

 

ASSEMBLY

veritcal track

BOTTOM SECTION

5/8”

roller

LAG

SCREW

locations

Quick install and fully adjustable

flagangle lag locations

using 5/16” x 1-5/8” lag screws.

Tighten lag screw securing bottom

jamb bracket to jamb, to maintain

5/8” spacing. Hang cable drum over

flagangle. Repeat for the right side.

JAMB

BRACKET

BOTTOM SECTION

quick install jamb bracket

lag

screw

INSTALLATION

8

Stacking Sections

 

 

 

Tools Needed:

NOTE: For door section identification

LOCK SECTION

see page 4.

 

Power Drill

 

NOTE: Make sure hinge leafs are flipped

 

7/16” Socket

down, when stacking another section

 

Driver

on top.

 

Place rollers in hinge tubes of the second section (lock section). With assistance, lift second section and guide rollers into the vertical tracks.

Align vertical marks in the upper

 

 

alignment sticker, with the lower

 

 

alignment sticker on right hand side

 

 

on the back of door. Keep sections

 

 

aligned and fasten hinges to connect

 

 

the sections using 1/4” - 14 x 5/8”

(2) 1/4” - 14 X 5/8”

(2) 1/4” - 14 X 5/8”

self-tapping screws. Repeat for other

section(s) except top section.

SELF-TAPPING SCREWS

SELF-TAPPING SCREWS

IMPORTANT: When securing the end

 

 

hinges to the sections with 1/4”

 

 

- 14 x 5/8” self-tapping screws,

 

Alignment

ensure they are attached as

 

stickers

shown in the illustrations above.

Left end hinge

Right end hinge

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local15 yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Important Notice Series 4 SectionTable of Contents Package Contents Door Section Identification Saw horses pair Power DrillTools Required 3/16 Drill BitsSuddenly, resulting in severe Torsion Spring RemovalFailure to use approved Winding bars can cause spring Energy to be releasedUnwind Springs TorqueMaster Spring RemovalBracket and Drive Gear Removing the Old Door Extension Spring RemovalOpening Preparing the OpeningInstallation Attaching Quick InstallFlagangle to Vertical Track Attaching Fully Adjustable Jamb Brackets Installing Fully AdjustableBottom Section DrumsStacking Sections Vertical TrackOperator Bracket Top Section Attaching Horizontal Track to Quick Install FlagangleAttaching Horizontal Track to Adjustable Flagangle Fall from Overhead Position Top BracketsTorqueMaster Spring Tube Center Bracket BushingAlways Determined from Inside Aid alignment Idrive InstallationPlug the motor power cord into Opener Opener back and forth slightly to helpCable Drum Installation End Brackets Drive Gear InstallationCounter Installation Positioning Support Bracket Handle Bracket Mounting DisconnectAttaching Disconnect Handle Important do not USE Impact GUN To Wind Springs Cable AdjustmentsSecuring Door For Spring WindingRecommended Spring Turns Setting Spring TensionVertical TRACKS. Adjustments to Winding Bolt RotationRear Support Drum Wrap InstallationSpring fittings may release from Adjust weather seal or door stop ifLevel and parallel with door Weather seal or door stop to both doorDo not Install Pull Ropes Side LockPull Rope Locate the center bracket, mark Gear assembly onto the TorqueMasterDoorMaster TM Bracket Center of the TorqueMaster spring TubeHeader Trolley OperatorMount operator to ceiling so that Result in Severe or Fatal InjuryImportant do not USE a Pressure Washer on Garage Door Cleaning Your Steel And Fiberglass Garage DoorGlass Cleaning Instructions Acrylic Cleaning InstructionsFiberglass Refinishing And Or Finishing Steel Preparation For PaintingBy a hard objects, or have been punctured Lifetime Limited Warranty Model
Related manuals
Manual 32 pages 11.46 Kb Manual 20 pages 42.88 Kb Manual 4 pages 60.02 Kb Manual 26 pages 11.64 Kb Manual 18 pages 4.37 Kb

9800 specifications

Wayne-Dalton is a well-known brand in the garage door industry, offering a wide range of models designed for durability, performance, and aesthetic appeal. Among its most popular series are the 9700, 5000, 8000, 9000, and 9800, each equipped with unique features and advanced technologies to meet diverse customer needs.

The Wayne-Dalton 9700 series is known for its combination of strength and insulation. This garage door is manufactured with a three-layer construction providing robust protection against the elements while offering excellent energy efficiency. The insulated steel construction can help maintain interior temperatures, making it ideal for attached garages.

The 5000 series, on the other hand, is designed for a more traditional look combined with modern performance. Featuring a lightweight design, it is made from durable materials that resist rust and corrosion. The 5000 series can be customized with different colors and styles, allowing homeowners to achieve the perfect aesthetic to enhance their property.

Moving on to the 8000 series, this model is designed for commercial applications and residential use where heavy-duty functions are necessary. It is built to withstand extreme weather conditions while providing optimal security with added strength features. The 8000 series offers smooth operation and minimal maintenance requirements, making it a great choice for those seeking reliability.

The 9000 series stands out with its stylish design and sleek finishes. This series offers advanced insulation options, coupled with numerous panel designs that provide a polished and sophisticated look. The 9000 model emphasizes both aesthetics and energy efficiency, making it a favorite among homeowners looking for a beautiful yet functional garage door.

Lastly, the 9800 series is the premium option within Wayne-Dalton’s offerings. This series is characterized by its high insulation value and thermal efficiency, thanks to its innovative construction techniques. The 9800 doors can be customized with numerous panel options and colors, delivering a luxury look while ensuring excellent performance.

In conclusion, Wayne-Dalton’s 9700, 5000, 8000, 9000, and 9800 series garage doors each feature distinctive characteristics and technologies aimed at enhancing durability, security, and aesthetics. Homeowners can find a reliable option within this range that suits their specific requirements, whether they prioritize insulation, style, or heavy-duty functionality. With Wayne-Dalton’s commitment to quality and innovation, these garage doors stand out in today’s market.
Top Page Image Contents