Wayne-Dalton 9800 Winding Bolt Rotation, Setting Spring Tension, Vertical TRACKS. Adjustments to

Page 30

28

Winding Bolt Rotation

 

Tools Needed:

See chart in Step 29 for proper spring

tension setting.

 

Power Drill

Beginning with the right hand side, ensure

the cable is in the first groove of the cable

 

 

drum. Apply light pressure to the canoe

7/16" Socket

clip on counter cover while winding

Driver

springs.

WARNING

 

Prior to winding or making adjustments to the springs, ensure you’re winding in the proper direction as stated in the Installation Instructions. Otherwise the spring fittings may release from spring if not wound in the proper direction and could result in severe or fatal injury. Using a power drill (high torque/gear reduced to 1300 RPM preferred) with a 7/16" socket, carefully rotate right hand winding bolt clockwise, until counter shows 2-3 turns.

This will keep the counterbalance cable taut while adjusting the left hand side counterbalance cable. Adjust left hand counterbalance cable tension. (refer to Step 27)

NOTE: Single spring applications require no spring winding on left hand side, but need cable tension adjusted.

NOTE: Ensure counterbalance cable tension is equal for both sides prior to fully winding spring(s) to appropriate number of turns.

Winding

Bolt

Canoe Clip

29

Setting Spring Tension

 

 

 

 

 

 

 

Tools Needed:

NOTE: Apply light pressure to the canoe clip on the

Spring

 

 

counter cover while winding spring(s). See the Spring

 

 

 

Tension

 

 

 

Turn chart.

 

 

Power Drill

Sample

 

 

For SINGLE SPRING applications, return to the right hand

 

 

 

Setting

 

 

7/16” Socket

side and carefully rotate the winding bolt head clockwise

 

 

 

until the counter shows the correct number of turns for

 

 

 

Driver

 

 

 

your door.

 

Lock Nut

 

 

 

7/16”

7/16" Wrench

For DOUBLE SPRING applications, remain on the left hand

 

 

side and carefully rotate the winding bolt head clockwise

 

 

Wrench

 

until the counter shows the correct number of turns for

 

 

 

 

your door. Then return to the right hand side and wind the

 

 

 

 

right hand spring to the required number of turns.

 

 

 

 

IMPORTANT: Do Not Overwind.

 

 

 

 

After spring is wound, hold the lock nut (in back of end

 

 

 

 

bracket) stationary on the right hand side with a 7/16”

 

 

 

 

wrench while rotating the winding bolt clockwise until

 

 

 

 

snug. Tightening of the lock nut prevents spring from

 

 

 

 

unwinding. Repeat for opposite side for double spring

 

 

 

 

TorqueMaster® systems.

NOTE: For 7’ high doors, 8’, 9’, 10’, 16’ or 18’ wide with

 

IMPORTANT: CAUTIOUSLY REMOVE VICE CLAMPS FROM

 

VERTICAL TRACKS. ADJUSTMENTS TO THE

windows, the recommended number of spring turns is 15.

 

RECOMMENDED NUMBER OF TURNS MAY BE REQUIRED.

RECOMMENDED SPRING TURNS

 

AFTER REAR SUPPORT ASSEMBLY IS COMPLETE (STEP

 

31), CHECK DOOR BALANCE. IF DOOR RAISES OFF FLOOR

 

idrive® Operated

Manually Operated Door,

 

UNDER SPRING TENSION ALONE, REDUCE SPRING

 

 

Door Height

Doors 11’-11”

and idrive® Operated

 

TENSION UNTIL DOOR RESTS ON THE FLOOR. IF THE

 

 

Wide or Less

Doors 12’ Wide or Greater

 

DOOR IS HARD TO RAISE OR DRIFTS DOWN ON ITS OWN,

 

 

 

 

 

 

ADD SPRING TENSION. AN UNBALANCED DOOR CAN

8’-0”

17-1/2

18

 

CAUSE IDRIVEvv OPERATION PROBLEMS.

 

 

 

30 Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Series 4 Section Important NoticeTable of Contents Package Contents Door Section Identification 3/16 Drill Bits Power DrillTools Required Saw horses pairEnergy to be released Torsion Spring RemovalFailure to use approved Winding bars can cause spring Suddenly, resulting in severeTorqueMaster Spring Removal Unwind SpringsBracket and Drive Gear Extension Spring Removal Removing the Old DoorPreparing the Opening OpeningInstallation Attaching Quick InstallFlagangle to Vertical Track Attaching Fully Adjustable Installing Fully Adjustable Jamb BracketsDrums Bottom SectionVertical Track Stacking SectionsOperator Bracket Top Section Quick Install Flagangle Attaching Horizontal Track toAttaching Horizontal Track to Adjustable Flagangle Top Brackets Fall from Overhead PositionTorqueMaster Spring Tube Center Bracket BushingAlways Determined from Inside Opener back and forth slightly to help Idrive InstallationPlug the motor power cord into Opener Aid alignmentCable Drum Installation Drive Gear Installation End BracketsCounter Installation Positioning Support Bracket Mounting Disconnect Handle BracketAttaching Disconnect Handle For Spring Winding Cable AdjustmentsSecuring Door Important do not USE Impact GUN To Wind SpringsWinding Bolt Rotation Setting Spring TensionVertical TRACKS. Adjustments to Recommended Spring TurnsDrum Wrap Installation Rear SupportWeather seal or door stop to both door Adjust weather seal or door stop ifLevel and parallel with door Spring fittings may release fromDo not Install Pull Ropes Side LockPull Rope Center of the TorqueMaster spring Tube Gear assembly onto the TorqueMasterDoorMaster TM Bracket Locate the center bracket, markResult in Severe or Fatal Injury Trolley OperatorMount operator to ceiling so that HeaderAcrylic Cleaning Instructions Cleaning Your Steel And Fiberglass Garage DoorGlass Cleaning Instructions Important do not USE a Pressure Washer on Garage DoorSteel Preparation For Painting Fiberglass Refinishing And Or FinishingLifetime Limited Warranty Model By a hard objects, or have been punctured
Related manuals
Manual 32 pages 11.46 Kb Manual 20 pages 42.88 Kb Manual 4 pages 60.02 Kb Manual 26 pages 11.64 Kb Manual 18 pages 4.37 Kb

9800 specifications

Wayne-Dalton is a well-known brand in the garage door industry, offering a wide range of models designed for durability, performance, and aesthetic appeal. Among its most popular series are the 9700, 5000, 8000, 9000, and 9800, each equipped with unique features and advanced technologies to meet diverse customer needs.

The Wayne-Dalton 9700 series is known for its combination of strength and insulation. This garage door is manufactured with a three-layer construction providing robust protection against the elements while offering excellent energy efficiency. The insulated steel construction can help maintain interior temperatures, making it ideal for attached garages.

The 5000 series, on the other hand, is designed for a more traditional look combined with modern performance. Featuring a lightweight design, it is made from durable materials that resist rust and corrosion. The 5000 series can be customized with different colors and styles, allowing homeowners to achieve the perfect aesthetic to enhance their property.

Moving on to the 8000 series, this model is designed for commercial applications and residential use where heavy-duty functions are necessary. It is built to withstand extreme weather conditions while providing optimal security with added strength features. The 8000 series offers smooth operation and minimal maintenance requirements, making it a great choice for those seeking reliability.

The 9000 series stands out with its stylish design and sleek finishes. This series offers advanced insulation options, coupled with numerous panel designs that provide a polished and sophisticated look. The 9000 model emphasizes both aesthetics and energy efficiency, making it a favorite among homeowners looking for a beautiful yet functional garage door.

Lastly, the 9800 series is the premium option within Wayne-Dalton’s offerings. This series is characterized by its high insulation value and thermal efficiency, thanks to its innovative construction techniques. The 9800 doors can be customized with numerous panel options and colors, delivering a luxury look while ensuring excellent performance.

In conclusion, Wayne-Dalton’s 9700, 5000, 8000, 9000, and 9800 series garage doors each feature distinctive characteristics and technologies aimed at enhancing durability, security, and aesthetics. Homeowners can find a reliable option within this range that suits their specific requirements, whether they prioritize insulation, style, or heavy-duty functionality. With Wayne-Dalton’s commitment to quality and innovation, these garage doors stand out in today’s market.
Top Page Image Contents