Wayne-Dalton 9800 installation instructions Top Section

Page 17

10

Top Section

 

Tools Needed:

Place the top section in the opening

Hammer

and vertically align with lower sections.

 

7/16” Socket

Align vertical marks in the upper

alignment sticker, with the lower

 

7/16” Wrench

alignment sticker on right hand side on

 

the back of door.

Ratchet Wrench

 

7/16” Socket

Temporarily secure the top section by

driving a nail in the header near the

Driver

center of the door and bending it over

 

Power Drill

the top section.

 

 

Now flip up hinge leafs, hold tight

 

against section, and fasten center

 

hinges first, and end hinges last. (Refer

 

to Step 8).

 

When installing a door with a

 

TorqueMaster® counterbalance system,

 

vertical track alignment is critical.

 

Position flagangle between 1-11/16”

 

(43 mm) to 1-3/4” (44 mm) from the

 

edge of the door. Tighten the bottom lag

 

screw. Flagangles must be parallel to

door width

+3-3/8” to 3-1/2”

Alignment stickers

INSTALLATION

the door sections. Repeat for opposite

side.

IMPORTANT: The dimension

between the flagangles must be

doorwidth plus 3-3/8” (86mm) to

3-1/2” (89 mm) for smooth, safe

door operation.

For quick install track:

Complete the vertical track installation

by securing the center jamb bracket(s)

and tightening the other lag screws.

Repeat for opposite side.

For fully adjustable track:

NAIL

top section

vERTICAL tRACK

ROLLER

ROLLER Against

VERTICAL TRACK

fully adjustable track

Complete the vertical track installation

by securing the center jamb bracket(s)

and tightening the other lag screws.

Push the vertical track against the

rollers so that the rollers are touching

the deepest part of the curved side of

the track (see illustration). Tighten all

the track bolts and nuts. Repeat for

opposite side.

1-11/16” TO 1-3/4”

top

SECTION

FLAGANGLE

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local17 yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Image 17
Contents Important Notice Series 4 SectionTable of Contents Package Contents Door Section Identification Tools Required Power Drill3/16 Drill Bits Saw horses pairFailure to use approved Winding bars can cause spring Torsion Spring RemovalEnergy to be released Suddenly, resulting in severeUnwind Springs TorqueMaster Spring RemovalBracket and Drive Gear Removing the Old Door Extension Spring RemovalOpening Preparing the OpeningFlagangle to Vertical Track InstallationAttaching Quick Install Attaching Fully Adjustable Jamb Brackets Installing Fully AdjustableBottom Section DrumsStacking Sections Vertical TrackOperator Bracket Top Section Attaching Horizontal Track to Quick Install FlagangleAttaching Horizontal Track to Adjustable Flagangle Fall from Overhead Position Top BracketsAlways Determined from Inside TorqueMaster Spring TubeCenter Bracket Bushing Plug the motor power cord into Opener Idrive InstallationOpener back and forth slightly to help Aid alignmentCable Drum Installation End Brackets Drive Gear InstallationCounter Installation Positioning Support Bracket Handle Bracket Mounting DisconnectAttaching Disconnect Handle Securing Door Cable AdjustmentsFor Spring Winding Important do not USE Impact GUN To Wind SpringsVertical TRACKS. Adjustments to Setting Spring TensionWinding Bolt Rotation Recommended Spring TurnsRear Support Drum Wrap InstallationLevel and parallel with door Adjust weather seal or door stop ifWeather seal or door stop to both door Spring fittings may release fromPull Rope Do not Install Pull RopesSide Lock DoorMaster TM Bracket Gear assembly onto the TorqueMasterCenter of the TorqueMaster spring Tube Locate the center bracket, markMount operator to ceiling so that Trolley OperatorResult in Severe or Fatal Injury HeaderGlass Cleaning Instructions Cleaning Your Steel And Fiberglass Garage DoorAcrylic Cleaning Instructions Important do not USE a Pressure Washer on Garage DoorFiberglass Refinishing And Or Finishing Steel Preparation For PaintingBy a hard objects, or have been punctured Lifetime Limited Warranty Model
Related manuals
Manual 32 pages 11.46 Kb Manual 20 pages 42.88 Kb Manual 4 pages 60.02 Kb Manual 26 pages 11.64 Kb Manual 18 pages 4.37 Kb

9800 specifications

Wayne-Dalton is a well-known brand in the garage door industry, offering a wide range of models designed for durability, performance, and aesthetic appeal. Among its most popular series are the 9700, 5000, 8000, 9000, and 9800, each equipped with unique features and advanced technologies to meet diverse customer needs.

The Wayne-Dalton 9700 series is known for its combination of strength and insulation. This garage door is manufactured with a three-layer construction providing robust protection against the elements while offering excellent energy efficiency. The insulated steel construction can help maintain interior temperatures, making it ideal for attached garages.

The 5000 series, on the other hand, is designed for a more traditional look combined with modern performance. Featuring a lightweight design, it is made from durable materials that resist rust and corrosion. The 5000 series can be customized with different colors and styles, allowing homeowners to achieve the perfect aesthetic to enhance their property.

Moving on to the 8000 series, this model is designed for commercial applications and residential use where heavy-duty functions are necessary. It is built to withstand extreme weather conditions while providing optimal security with added strength features. The 8000 series offers smooth operation and minimal maintenance requirements, making it a great choice for those seeking reliability.

The 9000 series stands out with its stylish design and sleek finishes. This series offers advanced insulation options, coupled with numerous panel designs that provide a polished and sophisticated look. The 9000 model emphasizes both aesthetics and energy efficiency, making it a favorite among homeowners looking for a beautiful yet functional garage door.

Lastly, the 9800 series is the premium option within Wayne-Dalton’s offerings. This series is characterized by its high insulation value and thermal efficiency, thanks to its innovative construction techniques. The 9800 doors can be customized with numerous panel options and colors, delivering a luxury look while ensuring excellent performance.

In conclusion, Wayne-Dalton’s 9700, 5000, 8000, 9000, and 9800 series garage doors each feature distinctive characteristics and technologies aimed at enhancing durability, security, and aesthetics. Homeowners can find a reliable option within this range that suits their specific requirements, whether they prioritize insulation, style, or heavy-duty functionality. With Wayne-Dalton’s commitment to quality and innovation, these garage doors stand out in today’s market.