Panasonic AJ-D750P Recording, 1Selecting video/audio input signals, Adjusting the video level

Page 26

Recording

Set the accidental erasure prevention tab on the cassette tape to the “recording” position and insert the tape.

Press the STOP button to place the unit in the stop mode.

Set the MODE switch to EE.

EE images now appear on the TV monitor.

Check that the REC INHIBIT lamp is off.

If this lamp is lighted, set the REC INHIBIT switch to OFF.

Select the video and audio input signals and adjust their levels.

5-1Selecting video/audio input signals

1Connect the signals to be recorded.

2 Select the input signals using the INPUT SELECT switches on the front panel.

The input signals corresponding to the lighted lamps have been selected.

5-2

5-3

Adjusting the video level

1 Keep the VIDEO LEVEL PRESET/MANUAL switch set to “PRESET” (unity value).

2 To adjust the recording level, set the VIDEO LEVEL PRESET/MANUAL switch to “MANUAL” and adjust the level to a position between +3dB and –3dB with the control.

Adjusting the audio level

1Adjust the audio input signal levels of the analog audio CH1/CH2 signals and

analog cue signal. Keep the audio input/output level controls pushed in (unity value).

2The audio signals will be recorded at the proper level.

To adjust the recording level, pull out the controls and adjust them. With the CUE signal, adjust the control in such a way that –20dB will not be exceeded.

Press the PLAY button while holding down the REC button. The REC and PLAY lamps light, and recording commences.

To end the recording, press the STOP button.

Recording is ended, and the unit goes into the stop mode.

<Notes>

Check that the SERVO lamp is lighted during recording. If it flashes or if it is off, the images played back will be disturbed.

Only the analog composite video input signals can be adjusted. (The digital video and analog component input signals cannot be adjusted.)

The sound and pictures to be recorded are offset from the playback pictures by at least 5 frames and recorded. When, for instance, recording sound at a particular timing while the playback pictures are monitored, the sound to be recorded will be recorded at a position which is offset from the playback pictures by 5 frames.

- 2 6 -

Image 26
Contents Operating Instructions FCC Note Contents AES/EBU audio input/output Analog input/outputSerial digital input/output Pin RS-422A/RS232C remoteAutomatic editing functions Controls and their functions Video Power switchInput Select switches AudioStop button Play buttonREC button FF buttonINT/EXT switch TC/CTL switchTC/UB switch TAPE/EE switch In the stop modeRemote lamp REMOTE/LOCAL switchSHTL/SLOW switch Search buttonPREVIEW/REVIEW buttons Preroll buttonAuto Edit button IN/SET/OUT buttonsCassette insertion display lamp Headphones jackTime code buttons Consumer cassette insertion display lampMonitor SET button Volume controlMonitor Select switches Chroma Level control and switch Encoder Control switchVideo Level control and switch SET UP control and switch Composite output only variableSET button REC Inhibit switchMenu button Diag buttonConnector area Controls and their functionsAnalog Audio in connectors AC in connectorSignal GND terminal CUE in connectorDigital Audio IN/OUT connector Analog Component Video OUT connectorAnalog Composite Video OUT connectors Remote control connectorsConnections when one unit is used Set the Control switch on the front panel to LocalRecorder Connections when 2 units are used deck to deckSource machine Connections with editing controller WFM General purpose cassette Description TapesType Consumer cassette AJ-P6MP, AJ-P12MP, AJ-P23MP, AJ-P33MP, AJ-P63MPSwitching on the power/inserting the cassette STOP/STAND by mode Still Timer SettingAdjusting the audio level 1Selecting video/audio input signalsAdjusting the video level RecordingPlayback Jog/shuttle modes Jog modeShuttle mode Manual editing Preroll Automatic editing Deck to Deck Switch settings and adjustments Automatic editingSelect the editing mode Negative duration function Entering the edit pointsMatch frame processing function Checking the edit points Calculating the durationModifying the edit points Resetting both the edit in and OUT pointsResetting either the edit in or OUT point Preview Retry function Executing automatic editingPostroll Auto tag editingReview L i t e d i t i n g Video level Video output encoder output signal adjustmentsSetup level Chroma level and hueSetup default settings SETUP-MENU Init SET YESPLAY/NOSTOPSetup setting menus Changing the fileSystem menu Display0005 Video OUT 3 connector 0012 User menu BasicSetup menus User menuUser menu Operation User menu Interface STD 301 IN/OUT DELNON-STD Servo REF EXTEdit Setting Step TimerSRC ProtectTime Code Binary PhaseDF Mode CorrUser menu Video CAMAudio Superimposed Fine REC CUEPB Fade ST2User bit Time code/user bitTime code Setting the internal time code Recording internal/external time codesReproducing the time code/user bit Characters displayed Operation modeSuperimpose screen Display positionMenu No setting? Servo referenceServo reference setting tables Audio V Fade Function Abbr Circuit Full name Function Factory settingPrinted circuit board NameRack mounting Connector signals Pin NoPin No Signal Signal Pin NoSignal Video head cleaning CondensationSpecifications Other input/output connectorPanasonic de Mexico S.A. de C.V