Panasonic AJ-D750P manual Video output encoder output signal adjustments, Video level, Setup level

Page 41

Video output (encoder output) signal adjustments

After this system has been connected, the video output signal (ENCODER OUT) must be adjusted if AB roll editing (editing using two source machines) using an editor, for instance, is to be error-free and accurate. (This adjustment must be repeated when one of the connecting cables has been replaced and whenever the connections are changed.)

The adjustment procedure using this unit is outlined below.

Check the connections. (see page 22.)

Set the REMOTE/LOCAL switch on the front panel bottom section to the adjustment

p o s i t i o n

( L O C A L ) .

REMOTE:

For adjusting the video output signals using an external encoder remote

controller.

LOCAL: For adjusting the video output signals using this unit.

Adjust the source machine independently.

3-1When using the preset values

Set the PRESET/MANUAL switches of the VIDEO LEVEL, CHROMA LEVEL, SETUP and HUE controls to PRESET.

3-2When adjusting the video output signals without using the preset values

1 Play back a cassette tape on which standard color bar signals have been recorded.

2 Adjust the controls in such a way that the waveforms on the waveform monitor (WFM) and vectorscope (VSC) resemble those shown in the figures below.

Video level

Adjust this level to 100IRE.

Chroma level and hue

Adjust the two controls in such a way that the light spot of the vector waveforms comes inside the rectangular grid mark.

Setup level

Adjust the control to eliminate deviation.

Waveform on WFM

Waveform on VSC

Perform the same adjustments on the source machine connected to the unit.

- 4 1 -

Image 41
Contents Operating Instructions FCC Note Contents Serial digital input/output Analog input/outputAES/EBU audio input/output Pin RS-422A/RS232C remoteAutomatic editing functions Controls and their functions Input Select switches Power switchVideo AudioREC button Play buttonStop button FF buttonTC/UB switch TC/CTL switchINT/EXT switch TAPE/EE switch In the stop modeSHTL/SLOW switch REMOTE/LOCAL switchRemote lamp Search buttonAuto Edit button Preroll buttonPREVIEW/REVIEW buttons IN/SET/OUT buttonsTime code buttons Headphones jackCassette insertion display lamp Consumer cassette insertion display lampMonitor SET button Volume controlMonitor Select switches Video Level control and switch Encoder Control switchChroma Level control and switch SET UP control and switch Composite output only variableMenu button REC Inhibit switchSET button Diag buttonControls and their functions Connector areaSignal GND terminal AC in connectorAnalog Audio in connectors CUE in connectorAnalog Composite Video OUT connectors Analog Component Video OUT connectorDigital Audio IN/OUT connector Remote control connectorsSet the Control switch on the front panel to Local Connections when one unit is usedRecorder Connections when 2 units are used deck to deckSource machine Connections with editing controller WFM Type Consumer cassette TapesGeneral purpose cassette Description AJ-P6MP, AJ-P12MP, AJ-P23MP, AJ-P33MP, AJ-P63MPSwitching on the power/inserting the cassette Still Timer Setting STOP/STAND by modeAdjusting the video level 1Selecting video/audio input signalsAdjusting the audio level RecordingPlayback Jog/shuttle modes Jog modeShuttle mode Manual editing Preroll Automatic editing Deck to Deck Automatic editing Switch settings and adjustmentsSelect the editing mode Negative duration function Entering the edit pointsMatch frame processing function Calculating the duration Checking the edit pointsModifying the edit points Resetting both the edit in and OUT pointsResetting either the edit in or OUT point Preview Postroll Executing automatic editingRetry function Auto tag editingReview L i t e d i t i n g Setup level Video output encoder output signal adjustmentsVideo level Chroma level and hueSETUP-MENU Init SET YESPLAY/NOSTOP Setup default settingsChanging the file Setup setting menusDisplay System menuUser menu Basic 0005 Video OUT 3 connector 0012User menu Setup menusUser menu Operation User menu Interface NON-STD Servo REF 301 IN/OUT DELSTD EXTEdit Setting SRC TimerStep ProtectTime Code DF Mode PhaseBinary CorrCAM User menu VideoAudio Superimposed PB Fade REC CUEFine ST2User bit Time code/user bitTime code Recording internal/external time codes Setting the internal time codeReproducing the time code/user bit Superimpose screen Operation modeCharacters displayed Display positionServo reference Menu No setting?Servo reference setting tables Audio V Fade Function Printed circuit board Factory settingAbbr Circuit Full name Function NameRack mounting Pin No Connector signalsPin No Signal Signal Pin NoSignal Condensation Video head cleaningOther input/output connector SpecificationsPanasonic de Mexico S.A. de C.V