JVC HR-S9700EK Select Preset to Watch, SET Counter Display, Reset Counter, Start Recording

Page 17

8

1 3

2

 

PR+/

RECORD

 

17

Record One Programme While Watching Another

SELECT PRESET TO WATCH

1 Once recording is in progress, all you need to do is to set the preset controls on the TV for the station you wish to view.

The programme selected with the TV’s preset controls appears on the TV screen while the one selected with the recorder's PR buttons is recorded on the tape.

Elapsed Recording Time

Indication

You can check the exact time of a recording.

1

2

0000

1

2

–:–

1 2 3

4

5

6

7 8 9

0

–:–

3

4

4

3

PR

 

1

 

SET COUNTER DISPLAY

 

 

Press –:–until a counter reading appears on the

 

 

display panel.

 

2

 

RESET COUNTER

 

 

Press 0000 before starting recording or playback.

 

 

 

 

 

The counter is reset to “0:00:00” and shows the exact

 

 

elapsed time as the tape runs.

 

 

 

 

Instant Timer Recording (ITR)

This easy method allows you to record for any length of time from 30 mins. to 6 hours (selectable in 30-min. increments), and shuts off the recorder after recording is finished.

START RECORDING

1 Press RECORD on the recorder.

ENGAGE ITR MODE

Tape Remaining Time

DISPLAY REMAINING TIME

1 Press –:–until the time remaining on the tape appears.

The display panel shows the tape remaining time with "" displayed.

By pressing the –:–button, you can change the display to show the counter reading, preset position*, clock time or tape remaining time.

*Preset position is not displayed during playback.

NOTE:

Depending on the type of tape used, there may be times when the tape remaining time reading may not appear right away, or is not correct. "– –:– –" may sometimes appear, or the display may blink on occasion.

2 Press RECORD again. "" blinks and 0:30 appears on the front display panel.

SET RECORDING

DURATION

3 If you want to record for more than 30 minutes, press RECORD to extend the time. Each press extends recording time by 30 minutes.

NOTE:

You can only perform ITR using the RECORD button on the recorder's front panel.

Image 17
Contents HR-S9700EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of Recorder Connect Video Recorder to TVBack of TV Video Connection Mains outlet Mains Power CordWith the AV or S-VIDEO connection Before performing the following procedure, make sure thatTion pg and the TV is turned on, Go to item10 or If -- appears on the display panel, refer Remote control while downloading isLink screen will appear. Then the Guide Program number setIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notAccess Mode SET Screen Access Main Menu ScreenLink Functions Turn on the RecorderSatellite Receiver Control Setting Enter Satellite RECEIVER’S Brand Select Satellite RECEIVER’S Channel for TestingCheck Result of Test Satellite Tuner Brand CodeLoad a Cassette PlaybackFind Programme Start Point Start PlaybackStill Picture/Frame-By-Frame Playback Slow MotionHigh-Speed Turbo Search Variable-Speed SearchRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayAccess Video PLUS+ Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Program Screen Enter Pluscode NumberPDC Recording Timer WarningEnter Programme Express Timer ProgrammingStart Time TimeTimer Mode SET PDC ModeSET Tape Speed Return to NormalCheck, Cancel And Replace Programmes Cancel or Change Programme Setting When programmes overlap each otherConfirm Overlapping Programmes ModifyNavigation Return to Normal Screen Check MemoryTurn OFF Navigation Turn Off NavigationTitle Editing Access Find Blank Space ScreenSelect Tape Number Load a CassetteEnter Character Access Video Navigation ScreenEdit Tape Title Select Tape NumberEdit Programme Title Category Select ProgrammeSelect Category Data Delete ProgrammeDelete Tape Data Delete Programme DataAccess Tape NO. Screen Access Find Title ScreenAccess Video Finding TitleSelect Programme Access Category Screen Access Date ScreenSelect Programme Load a Cassette Sorting By DateAdjust Tracking Playback Picture AdjustmentOverride Automatic Tracking ManuallyMode SET ModeDigital 3R Video StabilizerAdjust Audio Access REC LevelSelecting Sound You Want Control ScreenSoundtrack Selection Receiving Nicam Stereo And Bilingual ProgrammesDuring Playback Type of Broadcast On-screen Display Being ReceivedActivate Index Search Looking For Scene You WantSkip Over Unwanted SectionsSuper VHS S-VHS VHS ET and VHS Select S-VHS ModeRecording According To Tape Type S.T. Picture System Select B.E.S.T. ModePlayback/ Recording According To Tape Charac- teristics Recording Start PlaybackPlayback During B.E.S.TTimeScan Audio signal during TimeScanSearch Variable-Speed Search/ Reverse PlayTimeScan Audio TimeScanSpeed SP Speed LP Speed EP Audio output Forward Search Play Slow-Motion StillAutomatic Satellite Programme Recording Connector TV Aerial cable Audio in connectorSatellite Receiver Unit AerialSelect L-2 Select Mode Access Main Menu ScreenREC Mode ScreenRemove Power Supply Remote Control FunctionsSET Remote Control Code RE-SUPPLY PowerTV Multi-Brand Remote Control Control Your TV Using Additional ButtonsSET TV Brand Code Operate TVSET Satellite Receiver Satellite Receiver Multi- Brand Remote ControlBrand Code Operate Satellite ReceiverAccess Mode SET Access Main MenuControl SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Repeat steps 4 6 as necessary Synchro Edit connector Lanc Cable not providedSynchro Editing SET Edit Mode Input ModeEdit To Or From Another Video Recorder SET Recording DECK’SRecorder Player TV Receiver Player Your recorder RecorderSELECT/INPUT Setting OUTPUT/INPUT SettingLocate Start Point SET Input ModeEngage Audio Dubbing Start DubbingLocate END Point Reset the CounterInsert Editing Start Editing Engage Insert EditingEND Insert Editing DUBPrepare for Editing Random As- semble EditingLoad Source Cassette Press R.A.EDITLocate EDIT-OUT Point Locate EDIT-IN PointStart R.A.EDIT END R.A.EDITAccess Initial SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Jlip ID NO. SET Screen Information On J TerminalOther Functions ENABLE/DISABLEON-SCREEN Display On-Screen DisplayPress %Þ to move the highlight bar pointer to Select Power Save ModePower Save Mode Auto Timer Access Mode SET ScreenAuto SP→LP Timer Next Function MemoryResume Recording Engage RECORD-PAUSE ModeStop Playback Speaker Television Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelConnected TV is turned on With RF ConnectionInserted in the recorder Perform Auto Channel SET Tuner SetAuto Channel Set Pointer to Auto CHView Confirmation Screen Input Channel Storing Channels ManuallyEnter NEW Channel Information Close Confirmation ScreenChange Station Preset Position When Receiving a Scrambled BroadcastFine-Tuning Channels Already Stored Delete a ChannelEnter NEW Character Station Name TV Station And ID ListTV Station Channel Number Guide Clock Set Guide Program Number Set Video Plus+ System SetupNumber What happens if the tape runs out during recording? Questions And AnswersÄ remain lit on the display panel. Is there Problem? Troubleshooting Won’t stop blinking Record Safety tab removed Timer RecordingFront View Index3 4 5 6 @ # $ Inside View of Front PanelRear View VCR Display PanelTV Muting Button mutes sound Remote ControlFast Forward FF Button same as button on Remote Control LCDDA4 Double Azimuth helical Mm x 106 mm x 352 mmMaximum recording time