JVC LPT0320-001B Selecting Sound You Want, Access REC Level, Control Screen, Adjust Audio

Page 34

34ADVANCEDOPERATIONS(cont.)

Selecting The

Sound You

Want

Audio Recording Level Control

In most cases, setting the audio recording level control to the centre position will provide satisfactory results. If necessary, you can adjust the audio recording level more precisely by reffering to the audio level indicator on the front panel.

ACCESS MAIN MENU

SCREEN

1– –:– –

AUDIO

2

1 2 3

4

5

6

7 8 9

0

1

2

3

4

4

3

MENU

OK

	1 Press MENU.
		ACCESS REC LEVEL
		CONTROL SCREEN
		Press %Þ to move the	MAIN MENU
		highlight bar (pointer) to	MODE SET
	2 “REC LEVEL CTL”, then		MODE SET
	2 “REC LEVEL CTL”, then		AUTO CH SET
		press OK or #.	MANUAL CH SET
			OUTPUT/INPUT SET
			INITIAL SET
			REC LEVEL CTL
			R.A.EDIT
			VIDEO NAVIGATION
			[5°] =
			[MENU] : EXIT

		ADJUST AUDIO
	3	RECORDING LEVEL
	3	Press % or Þ.	REC LEVEL CTL
		Press % or Þ.

			MIN + * MAX

			[5°]
			[MENU] : EXIT

●Press % or Þ briefly 5 times to move the on-screen's audio levels by one division on the scale. To move the audio levels faster, keep % or Þ pressed.

●Adjust the recording level while watching the recorder's audio level meters. Set the level so that maximum volume causes the meters to vary between 0dB to 4dB.

RETURN TO NORMAL

SCREEN

4 Press MENU.

NOTES:

●Noise will increase if the recording level is too low, while distortion will increase if the level is too high.

●When you finished Audio recording, be sure to set the level control back to its centre position.

Image 34

Contents HR-S9700EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Connect Video Recorder to TVBack of Recorder Mains outlet Mains Power Cord Video ConnectionTion pg and the TV is turned on, Before performing the following procedure, make sure thatWith the AV or S-VIDEO connection Go to itemLink screen will appear. Then the Guide Remote control while downloading is10 or If -- appears on the display panel, refer Program number setIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedLink Functions Access Main Menu ScreenAccess Mode SET Screen Turn on the RecorderSatellite Receiver Control Setting Check Result of Test Select Satellite RECEIVER’S Channel for TestingEnter Satellite RECEIVER’S Brand Satellite Tuner Brand CodeFind Programme Start Point PlaybackLoad a Cassette Start PlaybackHigh-Speed Turbo Search Slow MotionStill Picture/Frame-By-Frame Playback Variable-Speed SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayAccess Video PLUS+ Program Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Enter Pluscode NumberTimer Warning PDC RecordingStart Time Express Timer ProgrammingEnter Programme TimeSET Tape Speed SET PDC ModeTimer Mode Return to NormalCheck, Cancel And Replace Programmes Confirm Overlapping Programmes When programmes overlap each otherCancel or Change Programme Setting ModifyNavigation Turn OFF Navigation Check MemoryReturn to Normal Screen Turn Off NavigationSelect Tape Number Access Find Blank Space ScreenTitle Editing Load a CassetteEdit Tape Title Access Video Navigation ScreenEnter Character Select Tape NumberSelect Category Select ProgrammeEdit Programme Title Category Delete Tape Data Delete ProgrammeData Delete Programme DataAccess Video Access Find Title ScreenAccess Tape NO. Screen Finding Title Select Programme Load a Cassette Access Date Screen Select Programme Access Category Screen Sorting By DateOverride Automatic Tracking Playback Picture AdjustmentAdjust Tracking ManuallyDigital 3R SET ModeMode Video StabilizerSelecting Sound You Want Access REC LevelAdjust Audio Control ScreenDuring Playback Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedSkip Over Unwanted Looking For Scene You WantActivate Index Search SectionsRecording According To Tape Type Select S-VHS ModeSuper VHS S-VHS VHS ET and VHS Playback/ Recording According To Tape Charac- teristics Select B.E.S.T. ModeS.T. Picture System Playback Start PlaybackRecording During B.E.S.TSearch Audio signal during TimeScanTimeScan Variable-Speed Search/ Reverse PlaySpeed SP Speed LP Speed EP Audio output TimeScanTimeScan Audio Forward Search Play Slow-Motion StillSatellite Receiver Unit Connector TV Aerial cable Audio in connectorAutomatic Satellite Programme Recording AerialREC Mode Access Main Menu ScreenSelect L-2 Select Mode ScreenSET Remote Control Code Remote Control FunctionsRemove Power Supply RE-SUPPLY PowerSET TV Brand Code Control Your TV Using Additional ButtonsTV Multi-Brand Remote Control Operate TVBrand Code Satellite Receiver Multi- Brand Remote ControlSET Satellite Receiver Operate Satellite ReceiverControl SET Mode Access Main MenuAccess Mode SET Minimizing Picture Degradation While EditingEdit From Camcorder Synchro Editing Synchro Edit connector Lanc Cable not providedRepeat steps 4 6 as necessary Edit To Or From Another Video Recorder Input ModeSET Edit Mode SET Recording DECK’STV Receiver Player Your recorder Recorder Recorder PlayerOUTPUT/INPUT Setting SELECT/INPUT SettingEngage Audio Dubbing SET Input ModeLocate Start Point Start DubbingInsert Editing Reset the CounterLocate END Point END Insert Editing Engage Insert EditingStart Editing DUBLoad Source Cassette Random As- semble EditingPrepare for Editing Press R.A.EDITStart R.A.EDIT Locate EDIT-IN PointLocate EDIT-OUT Point END R.A.EDITAccess Jlip ID NO. SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Information On J TerminalON-SCREEN Display ENABLE/DISABLEOther Functions On-Screen DisplayPower Save Mode Select Power Save ModePress %Þ to move the highlight bar pointer to Auto SP→LP Timer Access Mode SET ScreenAuto Timer Next Function MemoryStop Playback Engage RECORD-PAUSE ModeResume Recording Connection To Stereo System Speaker TelevisionVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelInserted in the recorder With RF ConnectionConnected TV is turned on Auto Channel Set Tuner SetPerform Auto Channel SET Pointer to Auto CHView Confirmation Screen Enter NEW Channel Information Storing Channels ManuallyInput Channel Close Confirmation ScreenFine-Tuning Channels Already Stored When Receiving a Scrambled BroadcastChange Station Preset Position Delete a ChannelEnter NEW Character TV Station And ID List Station NameTV Station Channel Number Guide Clock Set Number Video Plus+ System SetupGuide Program Number Set Ä remain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Timer Recording Won’t stop blinking Record Safety tab removedIndex Front ViewInside View of Front Panel 3 4 5 6 @ # $Rear View Display Panel VCRRemote Control TV Muting Button mutes soundRemote Control LCD Fast Forward FF Button same as button onMaximum recording time Mm x 106 mm x 352 mmDA4 Double Azimuth helical