JVC HR-S9700EK, LPT0320-001B Timer Recording, Won’t stop blinking Record Safety tab removed

							77
4.	Camcorder recording is not		● The camcorder has not been		Confirm that the camcorder is
	possible.		properly connected.		properly connected.
			● The input mode is not correct.		Set the input mode to “L-1”,“L-2”,
					“F-1” or “S-1”.
TIMER RECORDING
		SYMPTOM		POSSIBLE CAUSE		CORRECTIVE ACTION
1.	Timer recording won’t work.		● The clock and/or the timer have		Re-perform the clock and/or timer
			been set incorrectly.		settings.
			● The timer is not engaged.		Press ä and confirm that “ä“ is
					displayed on the display panel.
2.	Timer programming is not possible.		● Timer recording is in progress.		Timer programming can’t be
					performed while a timer recording is
					in progress. Wait until it finishes.
3.	“ä“ and “]“ on the display		● The timer is engaged but there’s no		Load a cassette with the Record
	panel won’t stop blinking.		cassette loaded.		Safety tab intact, or cover the hole
					using adhesive tape.
4.	The power shuts off and “ä“ and		● The loaded cassette has had its		Remove the cassette and cover the hole
	“]“ won’t stop blinking.		Record Safety tab removed.		with adhesive tape, or insert a cassette
			● The end of the tape was reached		with the Record Safety tab intact.
			during timer recording.		The programme may not have been
					recorded in its entirety. Next time
					make sure you have enough time on
					the tape to record the entire
					programme.
5.	“ä“ blinks for 10 seconds and the		● ä has been pressed when there are		Check the programmed data and re-
	Timer mode is disengaged.		no programs in memory, or the timer		programme as necessary, then press
			record information has been		ä again.
			programmed incorrectly.
6.	The VIDEO Plus+ system does not		● The recorder’s preset positions have		Refer to "Guide Program Number Set"
	timer-record properly.		been set incorrectly.		and re-perform the procedure (☞ pg. 74).
OTHER PROBLEMS
		SYMPTOM		POSSIBLE CAUSE		CORRECTIVE ACTION
1.	Whistling or howling is heard from		● The camcorder’s microphone is too		Position the camcorder so its
	the TV during camcorder record-		close to the TV.		microphone is away from the TV.
	ing.		● The TV’s volume is too high.		Turn the TV’s volume down.
2.	When scanning channels, some of		● Those channels have been desig-		If you need the skipped channels,
	them are skipped over.		nated to be skipped.		restore them (☞ pg. 68).
3.	The preset cannot be changed.		● Recording is in progress.		Press PAUSE to pause the recording,
					change presets, then press PLAY to
					resume recording.
4.	Channel settings that were made		● After the manual settings were		Perform manual setting again.
	manually seem to have changed or		made, Auto Channel Set was
	disappeared.		performed.
5.	No channels are stored in the		● The TV aerial cable was not		Turn off the recorder once and connect
	recorder's memory.		connected to the recorder when		the TV aerial cable to the recorder
			Auto Set Up was performed.		properly, then turn on the recorder
					again. The recorder will try Auto Set
					Up again (☞ pg. 8).
			● The fully-wired 21-pin SCART cable		Turn off the recorder once and connect
			was not connected between TV and		the fully-wired 21-pin SCART cable to
			the recorder when Preset Download		the recorder properly, then turn on the
			was performed.		recorder again. Then perform Preset
					Download again (☞ pg. 9).
6.	The remote control won’t operate		● The remote control brand setting is		Re-set the remote control to the
	the TV or satellite receiver.		incorrect.		correct brand (☞ pg. 45, 46).