JVC LPT0320-001B, HR-S9700EK Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 64

64SUBSIDIARYSETTINGS

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

8

13

2

IMPORTANT

Perform the following steps only if —

—Video Channel Set has not been done correctly by the Auto Set Up function (☞ pg. 8).

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.

●If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection), or via the provided RF cable, an S-Video cable and an audio cable (S-VIDEO connection), you do not need the video channel so you have to set the video channel to off. — Go to "With AV or S-VIDEO Connection" below.

●If you have connected the video recorder to your TV via the provided RF cable only (RF connection), you have to set the correct video channel — Go to "With RF Connection" on page 65.

1

2

1

2

– –:– –

1 2 3

4

5

6

7 8 9

0

3

4

4

3

OK

PR

With AV or S-VIDEO

Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■batteries have been installed in the remote control.

ACCESS VIDEO CHANNEL SET MODE

		Press and hold down STOP on the recorder until the
	1 display panel shows the following.
	2	SET VIDEO CHANNEL
	2	Press PR – until the display panel shows "–OUT– –".
		Press PR – until the display panel shows "–OUT– –".

●Now the video channel is set to off.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to its AV mode. Refer to the instructions supplied with your TV set for how to do this.

Image 64

Contents HR-S9700EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Connect Video Recorder to TVBack of Recorder Mains outlet Mains Power Cord Video ConnectionBefore performing the following procedure, make sure that With the AV or S-VIDEO connectionTion pg and the TV is turned on, Go to itemRemote control while downloading is 10 or If -- appears on the display panel, referLink screen will appear. Then the Guide Program number setIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedAccess Main Menu Screen Access Mode SET ScreenLink Functions Turn on the RecorderSatellite Receiver Control Setting Select Satellite RECEIVER’S Channel for Testing Enter Satellite RECEIVER’S BrandCheck Result of Test Satellite Tuner Brand CodePlayback Load a CassetteFind Programme Start Point Start PlaybackSlow Motion Still Picture/Frame-By-Frame PlaybackHigh-Speed Turbo Search Variable-Speed SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Enter ProgrammeStart Time TimeSET PDC Mode Timer ModeSET Tape Speed Return to NormalCheck, Cancel And Replace Programmes When programmes overlap each other Cancel or Change Programme SettingConfirm Overlapping Programmes ModifyNavigation Check Memory Return to Normal ScreenTurn OFF Navigation Turn Off NavigationAccess Find Blank Space Screen Title EditingSelect Tape Number Load a CassetteAccess Video Navigation Screen Enter CharacterEdit Tape Title Select Tape NumberSelect Category Select ProgrammeEdit Programme Title Category Delete Programme DataDelete Tape Data Delete Programme DataAccess Find Title Screen Access Tape NO. ScreenAccess Video Finding TitleAccess Date Screen Select Programme Access Category ScreenSelect Programme Load a Cassette Sorting By DatePlayback Picture Adjustment Adjust TrackingOverride Automatic Tracking ManuallySET Mode ModeDigital 3R Video StabilizerAccess REC Level Adjust AudioSelecting Sound You Want Control ScreenReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionDuring Playback Type of Broadcast On-screen Display Being ReceivedLooking For Scene You Want Activate Index SearchSkip Over Unwanted SectionsRecording According To Tape Type Select S-VHS ModeSuper VHS S-VHS VHS ET and VHS Playback/ Recording According To Tape Charac- teristics Select B.E.S.T. ModeS.T. Picture System Start Playback RecordingPlayback During B.E.S.TAudio signal during TimeScan TimeScanSearch Variable-Speed Search/ Reverse PlayTimeScan TimeScan AudioSpeed SP Speed LP Speed EP Audio output Forward Search Play Slow-Motion StillConnector TV Aerial cable Audio in connector Automatic Satellite Programme RecordingSatellite Receiver Unit AerialAccess Main Menu Screen Select L-2 Select ModeREC Mode ScreenRemote Control Functions Remove Power SupplySET Remote Control Code RE-SUPPLY PowerControl Your TV Using Additional Buttons TV Multi-Brand Remote ControlSET TV Brand Code Operate TVSatellite Receiver Multi- Brand Remote Control SET Satellite ReceiverBrand Code Operate Satellite ReceiverAccess Main Menu Access Mode SETControl SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Synchro Editing Synchro Edit connector Lanc Cable not providedRepeat steps 4 6 as necessary Input Mode SET Edit ModeEdit To Or From Another Video Recorder SET Recording DECK’STV Receiver Player Your recorder Recorder Recorder PlayerOUTPUT/INPUT Setting SELECT/INPUT SettingSET Input Mode Locate Start PointEngage Audio Dubbing Start DubbingInsert Editing Reset the CounterLocate END Point Engage Insert Editing Start EditingEND Insert Editing DUBRandom As- semble Editing Prepare for EditingLoad Source Cassette Press R.A.EDITLocate EDIT-IN Point Locate EDIT-OUT PointStart R.A.EDIT END R.A.EDITTerminal JLIPJoint Level Interface Protocol Connector Access Initial SET ScreenAccess Jlip ID NO. SET Screen Information On J TerminalENABLE/DISABLE Other FunctionsON-SCREEN Display On-Screen DisplayPower Save Mode Select Power Save ModePress %Þ to move the highlight bar pointer to Access Mode SET Screen Auto TimerAuto SP→LP Timer Next Function MemoryStop Playback Engage RECORD-PAUSE ModeResume Recording Connection To Stereo System Speaker TelevisionAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelInserted in the recorder With RF ConnectionConnected TV is turned on Tuner Set Perform Auto Channel SETAuto Channel Set Pointer to Auto CHView Confirmation Screen Storing Channels Manually Input ChannelEnter NEW Channel Information Close Confirmation ScreenWhen Receiving a Scrambled Broadcast Change Station Preset PositionFine-Tuning Channels Already Stored Delete a ChannelEnter NEW Character TV Station And ID List Station NameTV Station Channel Number Guide Clock Set Number Video Plus+ System SetupGuide Program Number Set Ä remain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Timer Recording Won’t stop blinking Record Safety tab removedIndex Front ViewInside View of Front Panel 3 4 5 6 @ # $Rear View Display Panel VCRRemote Control TV Muting Button mutes soundRemote Control LCD Fast Forward FF Button same as button onMaximum recording time Mm x 106 mm x 352 mmDA4 Double Azimuth helical