JVC LPT0320-001B, HR-S9700EK setup guide Stop Playback, Engage RECORD-PAUSE Mode, Resume Recording

Page 62

62

ADVANCEDOPERATIONS(cont.)

8

13

2

Repeat Playback

Your video recorder can automatically play back the whole tape 100 times repeatedly.

7 8 9

0

1

2

REW

STOP

JOG

4

4

3

FF

PAUSE

1		START PLAYBACK
1		Press PLAY.
2		ACTIVATE REPEAT PLAYBACK
		Press PLAY and hold for over 5 seconds, then release.

		● The Play indicator ( ) on the display panel blinks
		slowly.
		● The tape plays 100 times automatically, and then
		stops.

3		STOP PLAYBACK
3		Press STOP at any time to stop playback.

NOTES:

Retake

You can cut out unnecessary parts of a TV programme while you're recording it.

End of programme		Beginning of programme


Programme	Unnecessary	Unnecessary	Programme
	part	part

Recorded part

Go back to end of programme to cut out unnecessary part

ENGAGE RECORD-PAUSE MODE

1 Press PAUSE during recording.

LOCATE START POINT

2 Turn the JOG dial to the left or right (or hold down REW or FF) and release it when you reach the point where you want to resume recording.

* Your recorder returns to the Record-Pause mode.

RESUME RECORDING

3 Press PLAY when you wish to resume recording.

●Pressing PLAY, REW, FF or PAUSE also stops Repeat playback.

●Repeat playback is not possible with a cassette recorded in EP mode.

NTSC Playback

Your video recorder is equipped with NTSC circuitry that can play back NTSC tapes.

LOAD A CASSETTE

1 Insert a cassette recorded in NTSC.

START PLAYBACK

2 Press PLAY.

● "NTSC→PAL" appears on the screen for about 5 seconds.

● Some TVs shrink the picture vertically and place black bars at the top and bottom of the screen. This is not a malfunction on the part of either the video recorder or the TV.

● The picture may roll up and down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD control.)

● The counter and tape remaining time readings will be incorrect.

● During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour.

● Depending on the type of TV, the top and bottom portions of superimposed displays may be cut off during NTSC playback.

NOTES:

●Retake function does not work during Direct Rec (☞ pg. 11).

●Noise may appear when Retake function is used at the part that is recorded in EP mode.

Image 62

Contents HR-S9700EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of Recorder Connect Video Recorder to TVBack of TV Mains outlet Mains Power Cord Video ConnectionTion pg and the TV is turned on, Before performing the following procedure, make sure thatWith the AV or S-VIDEO connection Go to itemLink screen will appear. Then the Guide Remote control while downloading is10 or If -- appears on the display panel, refer Program number setIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedLink Functions Access Main Menu ScreenAccess Mode SET Screen Turn on the RecorderSatellite Receiver Control Setting Check Result of Test Select Satellite RECEIVER’S Channel for TestingEnter Satellite RECEIVER’S Brand Satellite Tuner Brand CodeFind Programme Start Point PlaybackLoad a Cassette Start PlaybackHigh-Speed Turbo Search Slow MotionStill Picture/Frame-By-Frame Playback Variable-Speed SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayAccess Video PLUS+ Program Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Enter Pluscode NumberTimer Warning PDC RecordingStart Time Express Timer ProgrammingEnter Programme TimeSET Tape Speed SET PDC ModeTimer Mode Return to NormalCheck, Cancel And Replace Programmes Confirm Overlapping Programmes When programmes overlap each otherCancel or Change Programme Setting ModifyNavigation Turn OFF Navigation Check MemoryReturn to Normal Screen Turn Off NavigationSelect Tape Number Access Find Blank Space ScreenTitle Editing Load a CassetteEdit Tape Title Access Video Navigation ScreenEnter Character Select Tape NumberEdit Programme Title Category Select ProgrammeSelect Category Delete Tape Data Delete ProgrammeData Delete Programme DataAccess Video Access Find Title ScreenAccess Tape NO. Screen Finding TitleSelect Programme Load a Cassette Access Date ScreenSelect Programme Access Category Screen Sorting By DateOverride Automatic Tracking Playback Picture AdjustmentAdjust Tracking ManuallyDigital 3R SET ModeMode Video StabilizerSelecting Sound You Want Access REC LevelAdjust Audio Control ScreenDuring Playback Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedSkip Over Unwanted Looking For Scene You WantActivate Index Search SectionsSuper VHS S-VHS VHS ET and VHS Select S-VHS ModeRecording According To Tape Type S.T. Picture System Select B.E.S.T. ModePlayback/ Recording According To Tape Charac- teristics Playback Start PlaybackRecording During B.E.S.TSearch Audio signal during TimeScanTimeScan Variable-Speed Search/ Reverse PlaySpeed SP Speed LP Speed EP Audio output TimeScanTimeScan Audio Forward Search Play Slow-Motion StillSatellite Receiver Unit Connector TV Aerial cable Audio in connectorAutomatic Satellite Programme Recording AerialREC Mode Access Main Menu ScreenSelect L-2 Select Mode ScreenSET Remote Control Code Remote Control FunctionsRemove Power Supply RE-SUPPLY PowerSET TV Brand Code Control Your TV Using Additional ButtonsTV Multi-Brand Remote Control Operate TVBrand Code Satellite Receiver Multi- Brand Remote ControlSET Satellite Receiver Operate Satellite ReceiverControl SET Mode Access Main MenuAccess Mode SET Minimizing Picture Degradation While EditingEdit From Camcorder Repeat steps 4 6 as necessary Synchro Edit connector Lanc Cable not providedSynchro Editing Edit To Or From Another Video Recorder Input ModeSET Edit Mode SET Recording DECK’STV Receiver Player Your recorder Recorder Recorder PlayerOUTPUT/INPUT Setting SELECT/INPUT SettingEngage Audio Dubbing SET Input ModeLocate Start Point Start DubbingLocate END Point Reset the CounterInsert Editing END Insert Editing Engage Insert EditingStart Editing DUBLoad Source Cassette Random As- semble EditingPrepare for Editing Press R.A.EDITStart R.A.EDIT Locate EDIT-IN PointLocate EDIT-OUT Point END R.A.EDITAccess Jlip ID NO. SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Information On J TerminalON-SCREEN Display ENABLE/DISABLEOther Functions On-Screen DisplayPress %Þ to move the highlight bar pointer to Select Power Save ModePower Save Mode Auto SP→LP Timer Access Mode SET ScreenAuto Timer Next Function MemoryResume Recording Engage RECORD-PAUSE ModeStop Playback Connection To Stereo System Speaker TelevisionVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelConnected TV is turned on With RF ConnectionInserted in the recorder Auto Channel Set Tuner SetPerform Auto Channel SET Pointer to Auto CHView Confirmation Screen Enter NEW Channel Information Storing Channels ManuallyInput Channel Close Confirmation ScreenFine-Tuning Channels Already Stored When Receiving a Scrambled BroadcastChange Station Preset Position Delete a ChannelEnter NEW Character TV Station And ID List Station NameTV Station Channel Number Guide Clock Set Guide Program Number Set Video Plus+ System SetupNumber What happens if the tape runs out during recording? Questions And AnswersÄ remain lit on the display panel. Is there Problem? Troubleshooting Timer Recording Won’t stop blinking Record Safety tab removedIndex Front ViewInside View of Front Panel 3 4 5 6 @ # $Rear View Display Panel VCRRemote Control TV Muting Button mutes soundRemote Control LCD Fast Forward FF Button same as button onDA4 Double Azimuth helical Mm x 106 mm x 352 mmMaximum recording time