JVC HR-S9700EK Access Main Menu Screen, Select L-2 Select Mode, Engage Auto Satellite Prog

Page 43

43

SATä indicator

ATTENTION

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on.

●If you have connected another appliance other than a satellite receiver to the AV2 (L-2) IN/DECODER connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on.

●Auto Satellite Prog recording and timer-recording cannot be done at the same time.

●When you press and hold the recorder's SATäbutton to engage the Auto Satellite Prog Rec mode, if the SATä indicator does not light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work properly with that satellite receiver*.

If this is the case, perform "Express Timer Programming" (☞ pg. 20) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite receivers.

NOTES:

Before performing the following steps:

●Make sure the satellite receiver is connected to the recorder's AV2 (L-2) IN/DECODER connector. (☞ pg. 42)

●Programme the timer on the satellite receiver.

●Insert a cassette with the safety tab in place.

ACCESS MAIN MENU SCREEN

1 Press MENU.

 

 

 

 

 

ACCESS OUTPUT/INPUT SET

 

 

 

2

SCREEN

 

 

 

 

Move the highlight bar (pointer) to "OUTPUT/INPUT

SET" by pressing %Þ, then press OK or #.

 

 

 

 

SELECT L-2 SELECT MODE

 

 

 

 

Move the highlight bar

OUTPUT/INPUT SET

 

(pointer) to "L-2 SELECT",

L-1 OUTPUT

VIDEO

3 by pressing %Þ, then press

L-1 INPUT

VIDEO

 

OK or #to set to "SAT" or

 

 

 

 

 

L-2 SELECT

SAT

 

 

 

"A/V". Then press MENU.

 

 

L-2 INPUT

VIDEO

 

 

 

 

 

 

 

 

 

 

[5°] =

 

 

 

 

 

[MENU] : EXIT

 

 

 

 

 

 

 

 

 

 

SET TAPE SPEED

 

 

 

 

4 Press SP/LP/EP ( ) to set the tape speed.

 

 

 

 

ENGAGE AUTO SATELLITE PROG

 

REC MODE

 

 

 

 

 

Press and hold SATä for about 2 seconds. The SATä

 

indicator lights up and the recorder turns off automati-

5 cally.

 

 

 

 

●To disengage the Auto Satellite Prog Rec mode, press SATä. The SATä indicator goes off.

●If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode.

●Auto Satellite Prog recording is possible with the AV2 (L-2) IN/DECODER connector only.

●When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON".

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer.

●The SAT ä indicator blinks while Auto Satellite Prog recording is in progress.

●Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengages the Auto Satellite Prog Rec mode.

●If there is more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 4 will apply to all the programmes for Auto Satellite Prog recording.

●The B.E.S.T. system (☞ pg. 38) does not work while Auto Satellite Prog recording is in progress.

●Just Clock (☞ pg. 73) does not work when the Auto Satellite Prog Rec mode is engaged.

●Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite Prog recording even though the SAT ä indicator blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer and is connected to the recorder's AV2 (L-2) IN/DECODER connector.

Page 42 Page 44
Image 43
Page 42 Page 44
Contents HR-S9700EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Connect Video Recorder to TVBack of Recorder Video Connection Mains outlet Mains Power CordGo to item Before performing the following procedure, make sure thatWith the AV or S-VIDEO connection Tion pg and the TV is turned on,Program number set Remote control while downloading is10 or If -- appears on the display panel, refer Link screen will appear. Then the GuideIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notTurn on the Recorder Access Main Menu ScreenAccess Mode SET Screen Link FunctionsSatellite Receiver Control Setting Satellite Tuner Brand Code Select Satellite RECEIVER’S Channel for TestingEnter Satellite RECEIVER’S Brand Check Result of TestStart Playback PlaybackLoad a Cassette Find Programme Start PointVariable-Speed Search Slow MotionStill Picture/Frame-By-Frame Playback High-Speed Turbo SearchRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeEnter Pluscode Number Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Access Video PLUS+ Program ScreenPDC Recording Timer WarningTime Express Timer ProgrammingEnter Programme Start TimeReturn to Normal SET PDC ModeTimer Mode SET Tape SpeedCheck, Cancel And Replace Programmes Modify When programmes overlap each otherCancel or Change Programme Setting Confirm Overlapping ProgrammesNavigation Turn Off Navigation Check MemoryReturn to Normal Screen Turn OFF NavigationLoad a Cassette Access Find Blank Space ScreenTitle Editing Select Tape NumberSelect Tape Number Access Video Navigation ScreenEnter Character Edit Tape TitleSelect Category Select ProgrammeEdit Programme Title Category Delete Programme Data Delete ProgrammeData Delete Tape DataFinding Title Access Find Title ScreenAccess Tape NO. Screen Access VideoSorting By Date Access Date ScreenSelect Programme Access Category Screen Select Programme Load a CassetteManually Playback Picture AdjustmentAdjust Tracking Override Automatic TrackingVideo Stabilizer SET ModeMode Digital 3RControl Screen Access REC LevelAdjust Audio Selecting Sound You WantType of Broadcast On-screen Display Being Received Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackSections Looking For Scene You WantActivate Index Search Skip Over UnwantedRecording According To Tape Type Select S-VHS ModeSuper VHS S-VHS VHS ET and VHS Playback/ Recording According To Tape Charac- teristics Select B.E.S.T. ModeS.T. Picture System During B.E.S.T Start PlaybackRecording PlaybackVariable-Speed Search/ Reverse Play Audio signal during TimeScanTimeScan SearchForward Search Play Slow-Motion Still TimeScanTimeScan Audio Speed SP Speed LP Speed EP Audio outputAerial Connector TV Aerial cable Audio in connectorAutomatic Satellite Programme Recording Satellite Receiver UnitScreen Access Main Menu ScreenSelect L-2 Select Mode REC ModeRE-SUPPLY Power Remote Control FunctionsRemove Power Supply SET Remote Control CodeOperate TV Control Your TV Using Additional ButtonsTV Multi-Brand Remote Control SET TV Brand CodeOperate Satellite Receiver Satellite Receiver Multi- Brand Remote ControlSET Satellite Receiver Brand CodeMinimizing Picture Degradation While Editing Access Main MenuAccess Mode SET Control SET ModeEdit From Camcorder Synchro Editing Synchro Edit connector Lanc Cable not providedRepeat steps 4 6 as necessary SET Recording DECK’S Input ModeSET Edit Mode Edit To Or From Another Video RecorderRecorder Player TV Receiver Player Your recorder RecorderSELECT/INPUT Setting OUTPUT/INPUT SettingStart Dubbing SET Input ModeLocate Start Point Engage Audio DubbingInsert Editing Reset the CounterLocate END Point DUB Engage Insert EditingStart Editing END Insert EditingPress R.A.EDIT Random As- semble EditingPrepare for Editing Load Source CassetteEND R.A.EDIT Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A.EDITInformation On J Terminal Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Access Jlip ID NO. SET ScreenOn-Screen Display ENABLE/DISABLEOther Functions ON-SCREEN DisplayPower Save Mode Select Power Save ModePress %Þ to move the highlight bar pointer to Next Function Memory Access Mode SET ScreenAuto Timer Auto SP→LP TimerStop Playback Engage RECORD-PAUSE ModeResume Recording Speaker Television Connection To Stereo SystemSET Video Channel Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetInserted in the recorder With RF ConnectionConnected TV is turned on Pointer to Auto CH Tuner SetPerform Auto Channel SET Auto Channel SetView Confirmation Screen Close Confirmation Screen Storing Channels ManuallyInput Channel Enter NEW Channel InformationDelete a Channel When Receiving a Scrambled BroadcastChange Station Preset Position Fine-Tuning Channels Already StoredEnter NEW Character Station Name TV Station And ID ListTV Station Channel Number Guide Clock Set Number Video Plus+ System SetupGuide Program Number Set Ä remain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Won’t stop blinking Record Safety tab removed Timer RecordingFront View Index3 4 5 6 @ # $ Inside View of Front PanelRear View VCR Display PanelTV Muting Button mutes sound Remote ControlFast Forward FF Button same as button on Remote Control LCDMaximum recording time Mm x 106 mm x 352 mmDA4 Double Azimuth helical
Top Page Image Contents