JVC LPT0320-001B, HR-S9700EK setup guide OUTPUT/INPUT Setting, SELECT/INPUT Setting

Page 52

52ADVANCEDOPERATIONS(cont.)

L-1 OUTPUT/INPUT Setting

The AV1 (L-1) IN/OUT connector accepts and delivers either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set "L-1 OUTPUT" and "L-1 INPUT" to the appropriate mode depending on the type of unit connected to the rear panel AV1 (L-1) IN/OUT connector of this recorder.

1Press MENU to access the Main Menu screen.

2Press %Þ to move the highlight bar (pointer) to "OUTPUT/INPUT SET", then press OK or #.

3 Press %Þ to move the highlight bar (pointer) to "L-1 OUTPUT" or "L-1 INPUT".

4 For "L-1 OUTPUT"

Press OK or #to select "VIDEO" or "S-VIDEO".

a–VIDEO

: If a connected device's input is compatible only with regular video signals,

 

set to "VIDEO".

b–S-VIDEO

: If a connected device's input is compatible with Y/C signals, set to

 

"S-VIDEO". This setting will let you take advantage of higher-quality

 

S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that

 

is compatible with the Y/C signal.)

For "L-1 INPUT"

Press OK or #to select "VIDEO" or "S-VIDEO".

a–VIDEO

: If a connected device's output is compatible only with regular video

 

signals, set to "VIDEO".

b–S-VIDEO

: If a connected device's output is compatible with Y/C signals, set to

 

"S-VIDEO". This setting will let you take advantage of higher-quality

 

S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that

 

is compatible with the Y/C signal.)

5Press MENU to return to normal screen.

●If "L-1 OUTPUT" is set to "S-VIDEO", it is impossible to set "L-1 INPUT" to "S-VIDEO".

●If "L-2 SELECT" is set to "DECODER", it is impossible to set "L-1 INPUT" to "S-VIDEO".

 

OUTPUT/INPUT SET

 

 

L-1 OUTPUT

VIDEO

L-1

INPUT

VIDEO

L-2

SELECT

A/V

L-2

INPUT

VIDEO

[5°] = [MENU] : EXIT

L-2 SELECT/INPUT Setting

The AV2 (L-2) IN/DECODER connector accepts either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set "L-2 SELECT" to the appropriate mode depending on the type of unit connected to the rear panel AV2 (L-2) IN/DECODER connector of this recorder. Set "L-2 INPUT" to the appropriate mode depending on the output signals of the connected unit.

1Press MENU to access the Main Menu screen.

2Press %Þ to move the highlight bar (pointer) to "OUTPUT/INPUT SET", then press OK or #.

3 Press %Þ to move the highlight bar (pointer) to "L-2 SELECT" or "L-2 INPUT".

4 For "L-2 SELECT"

OUTPUT/INPUT SET

Press OK or #to select "A/V", "DECODER" or "SAT".

L-1 OUTPUT

VIDEO

a–A/V

: To use this recorder as the recording deck with the player connected to the

L-1 INPUT

VIDEO

 

AV2 (L-2) IN/DECODER connector, or to use the satellite receiver con-

 

 

 

 

L-2 SELECT

A/V

 

 

nected to the AV2 (L-2) IN/DECODER connector.

 

b–DECODER

L-2 INPUT

VIDEO

 

: To use a decoder connected to the AV2 (L-2) IN/DECODER connector.

 

 

 

c–SAT

: To view a satellite programme with the TV set while the recorder is turned

 

 

 

 

off. (☞ pg. 42)

 

 

 

 

[5°] =

 

 

For "L-2 INPUT"

[MENU] : EXIT

 

 

Press OK or #to select "VIDEO" or "S-VIDEO".

 

 

 

a–VIDEO

: If a connected device's output is compatible only with regular video

 

 

 

 

signals, set to "VIDEO".

 

 

 

b–S-VIDEO

: If a connected device's output is compatible with Y/C signals, set to

 

 

 

 

"S-VIDEO". This setting will let you take advantage of higher-quality S-VHS

 

 

 

 

pictures. (For connection, be sure to use a 21-pin SCART cable that is

 

 

 

 

compatible with the Y/C signal.)

 

 

 

5Press MENU to return to normal screen.

●If you have a satellite receiver or a decoder connected to the AV2 (L-2) IN/DECODER connector, be sure to set "L-2 SELECT" back to appropriate mode after editing.

●If you're not connecting a satellite receiver or a decoder to the AV2 (L-2) IN/DECODER connector, leave "L-2 SELECT" set to "A/V".

●The default setting is "A/V"; if the recorder's memory backup has expired due to a power cut or because the AC was removed from the recorder, "A/V" will be automatically selected when the power is restored to the recorder. If you are using a satellite receiver or a decoder, be sure to set "L-2 SELECT" back to appropriate mode.

●When "L-2 SELECT" is set to "SAT", "SAT" appears on screen or display panel instead of "L-2" or "L2".

●If "L-2 SELECT" is set to "DECODER", it is impossible to set "L-2 INPUT" to "S-VIDEO".

●If "L-1 OUTPUT" is set to "S-VIDEO", it is impossible to set "L-2 SELECT" to "DECODER".

Page 51 Page 53
Image 52
Page 51 Page 53
Contents HR-S9700EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Connect Video Recorder to TVBack of Recorder Mains outlet Mains Power Cord Video ConnectionBefore performing the following procedure, make sure that With the AV or S-VIDEO connectionTion pg and the TV is turned on, Go to itemRemote control while downloading is 10 or If -- appears on the display panel, referLink screen will appear. Then the Guide Program number setIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedAccess Main Menu Screen Access Mode SET ScreenLink Functions Turn on the RecorderSatellite Receiver Control Setting Select Satellite RECEIVER’S Channel for Testing Enter Satellite RECEIVER’S BrandCheck Result of Test Satellite Tuner Brand CodePlayback Load a CassetteFind Programme Start Point Start PlaybackSlow Motion Still Picture/Frame-By-Frame PlaybackHigh-Speed Turbo Search Variable-Speed SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Enter ProgrammeStart Time TimeSET PDC Mode Timer ModeSET Tape Speed Return to NormalCheck, Cancel And Replace Programmes When programmes overlap each other Cancel or Change Programme SettingConfirm Overlapping Programmes ModifyNavigation Check Memory Return to Normal ScreenTurn OFF Navigation Turn Off NavigationAccess Find Blank Space Screen Title EditingSelect Tape Number Load a CassetteAccess Video Navigation Screen Enter CharacterEdit Tape Title Select Tape NumberSelect Category Select ProgrammeEdit Programme Title Category Delete Programme DataDelete Tape Data Delete Programme DataAccess Find Title Screen Access Tape NO. ScreenAccess Video Finding TitleAccess Date Screen Select Programme Access Category ScreenSelect Programme Load a Cassette Sorting By DatePlayback Picture Adjustment Adjust TrackingOverride Automatic Tracking ManuallySET Mode ModeDigital 3R Video StabilizerAccess REC Level Adjust AudioSelecting Sound You Want Control ScreenReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionDuring Playback Type of Broadcast On-screen Display Being ReceivedLooking For Scene You Want Activate Index SearchSkip Over Unwanted SectionsRecording According To Tape Type Select S-VHS ModeSuper VHS S-VHS VHS ET and VHS Playback/ Recording According To Tape Charac- teristics Select B.E.S.T. ModeS.T. Picture System Start Playback RecordingPlayback During B.E.S.TAudio signal during TimeScan TimeScanSearch Variable-Speed Search/ Reverse PlayTimeScan TimeScan AudioSpeed SP Speed LP Speed EP Audio output Forward Search Play Slow-Motion StillConnector TV Aerial cable Audio in connector Automatic Satellite Programme RecordingSatellite Receiver Unit AerialAccess Main Menu Screen Select L-2 Select ModeREC Mode ScreenRemote Control Functions Remove Power SupplySET Remote Control Code RE-SUPPLY PowerControl Your TV Using Additional Buttons TV Multi-Brand Remote ControlSET TV Brand Code Operate TVSatellite Receiver Multi- Brand Remote Control SET Satellite ReceiverBrand Code Operate Satellite ReceiverAccess Main Menu Access Mode SETControl SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Synchro Editing Synchro Edit connector Lanc Cable not provided Repeat steps 4 6 as necessary Input Mode SET Edit ModeEdit To Or From Another Video Recorder SET Recording DECK’STV Receiver Player Your recorder Recorder Recorder PlayerOUTPUT/INPUT Setting SELECT/INPUT SettingSET Input Mode Locate Start PointEngage Audio Dubbing Start DubbingInsert Editing Reset the CounterLocate END Point Engage Insert Editing Start EditingEND Insert Editing DUBRandom As- semble Editing Prepare for EditingLoad Source Cassette Press R.A.EDITLocate EDIT-IN Point Locate EDIT-OUT PointStart R.A.EDIT END R.A.EDITTerminal JLIPJoint Level Interface Protocol Connector Access Initial SET ScreenAccess Jlip ID NO. SET Screen Information On J TerminalENABLE/DISABLE Other FunctionsON-SCREEN Display On-Screen DisplayPower Save Mode Select Power Save ModePress %Þ to move the highlight bar pointer to Access Mode SET Screen Auto TimerAuto SP→LP Timer Next Function MemoryStop Playback Engage RECORD-PAUSE ModeResume Recording Connection To Stereo System Speaker TelevisionAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelInserted in the recorder With RF ConnectionConnected TV is turned on Tuner Set Perform Auto Channel SETAuto Channel Set Pointer to Auto CHView Confirmation Screen Storing Channels Manually Input ChannelEnter NEW Channel Information Close Confirmation ScreenWhen Receiving a Scrambled Broadcast Change Station Preset PositionFine-Tuning Channels Already Stored Delete a ChannelEnter NEW Character TV Station And ID List Station NameTV Station Channel Number Guide Clock Set Number Video Plus+ System SetupGuide Program Number Set Ä remain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Timer Recording Won’t stop blinking Record Safety tab removedIndex Front ViewInside View of Front Panel 3 4 5 6 @ # $Rear View Display Panel VCRRemote Control TV Muting Button mutes soundRemote Control LCD Fast Forward FF Button same as button onMaximum recording time Mm x 106 mm x 352 mmDA4 Double Azimuth helical
Top Page Image Contents