JVC HR-J480EU, HR-J280EU, HR-J281EU, HR-J289EU specifications Playback, Recording

Page 21

EN 21

B.E.S.T. Picture System

The B.E.S.T. (Biconditional Equalised Signal Tracking) system checks the condition of the tape in use during playback and recording, and compensates to provide the highest-possible playback and recording pictures. You can set “B.E.S.T.” to “ON” or “OFF” to your preference ( pg. 35).

Playback

The recorder assesses the quality of the tape once you initiate playback.

●The recorder adjusts the playback picture quality based on the quality of the tape in use.

●B.E.S.T. is active during Auto Tracking. “bESt” appears blinking on the recorder’s front display panel.

NOTES:

●When watching a tape recorded with “B.E.S.T.” set to “ON”, it is recommended that you leave B.E.S.T. on during playback as well.

●When watching a rental tape or one recorded on another

video recorder, or when using this recorder as the player for editing, set B.E.S.T. to your preference ( pg. 35).

●“bESt” only appears at the beginning of automatic tracking. Even though it doesn’t appear after that, the B.E.S.T. function is operative.

Recording

The recorder assesses the quality of the tape once you initiate recording.

DURING B.E.S.T.

B.E.S.T. COMPLETE

●The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording.

NOTES:

●With HR-J480EU:

The B.E.S.T. system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording.

With HR-J280/281/289EU:

The B.E.S.T. system works only after a tape has been inserted and the Record mode is first initiated. It does not work during recording.

●The B.E.S.T. system does not work while Auto Satellite Programme Recording is in progress ( pg. 28).

●In the case of timer recordings, the B.E.S.T. system works before recording is initiated.

●Once the cassette is ejected, the B.E.S.T. data is cancelled. The next time the cassette is used for recording, B.E.S.T. is re-performed.

●Pressing the recorder’s 7 button while “bESt” is displayed does not start Instant Timer Recording ( pg. 19).

ATTENTION

Since the B.E.S.T. system works before recording actually starts, there is a delay of approximately 7 seconds after 7 and 4 on the remote control are pressed, or 7 on the recorder is pressed. To make sure you record the desired scene or programme in its entirety, first perform the following steps:

APress and hold 9 and press 7 to engage the Record Pause mode.

●The recorder then automatically checks the condition of the tape and, after approximately 7 seconds, re-enters Record Pause.

BPress 4 to start recording.

If you want to bypass the B.E.S.T. system and begin recording immediately, set “B.E.S.T.” to “OFF” ( pg. 35).

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Video Cassette Recorder English Safety Precautions Moisture Condensation Front View Front Display Panel ON-SCREEN Display Operating JVC TVs How To UseSituate the recorder Check the contentsConnect the recorder to TV Connect the recorder to mainsTurn on the recorder Auto Set UpSelect your country Before starting, make sure of the followingSelect the language Perform Auto Set UpOn the front display panel On the on-screen display10 EN Perform Preset DownloadSet the video channel Press rt to select CH - and press OK or eJust Clock Language for the on-screen displayAccess the Country Set screen Access the Main Menu screenLanguage 12 ENLink Functions NexTView Link TV Auto Power OnVCR Auto Standby Direct Rec14 EN Basic PlaybackHigh-Speed Search Slow MotionVariable Speed Search Pause during playback16 EN Manual TrackingInstant ReView Skip Search Index SearchNext Function Memory Repeat Playback18 EN Engage the ITR mode Instant Timer Recording ITRWatching Another Set the recording duration20 EN Reset the counterTape Remaining Time Display the counterRecording PlaybackBefore performing the Showview Timer Programming Access the Showview screen22 EN Enter the Showview numberEngage the recorder’s timer mode Set the VPS/PDC modePress SP/LP p Press VPS/PDC to select on or OFF24 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR +Cancel or change a programme Check, cancel and change programmesReturn to the timer mode Disengage the timer modeCancel or change programme setting Confirm the overlapping programmesSelect the programme to modify Engage the Auto Satellite Programme Recording mode Select the L-2 Select modeProgramme Recording 28 ENEdit From a Camcorder Another Video Recorder Set the input mode of recording deck30 EN Start the source playerConnecting To a Satellite Receiver 32 EN Select the input modeConnect the decoder Set the tunerAccess the Initial Set screen Showview System SetupGuide Program Number Set Guide Program NumberAccess the Mode Set screen Mode SetSelect the mode Select the mode settingThis feature helps you to adjust the playback picture You can set the B.E.S.T. Biconditional Equalised SignalWhen this function is set to ON, the timer is Off, and automatically disengaged when the recorder isFor Example 36 ENAbout Ntsc Playback Tuner Set Access the Auto Channel Set screen38 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice Manual Channel Set 40 ENDelete a Channel When Receiving a Scrambled Broadcast42 EN Set Stations aSet Stations B Station Name TV Station And ID ListAccess the Clock Set screen Clock Set44 EN Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operationExit the Video Channel Set mode Access the Video Channel Set modeVideo Channel Set 46 ENPower Recording 48 ENOther Problems Playback 50 ENConnecting To a Satellite Receiver Auto Channel Set Auto Set UpTimer warning display Tuner Set Watching AnotherMonochrome signal, 625 lines Signal systemMemory backup time Approx min LP HR-J480EU only 480 min. with E-240 video cassette
Top Page Image Contents