JVC HR-J480EU, HR-J280EU, HR-J281EU, HR-J289EU specifications About Ntsc Playback

Page 37

 

 

EN 37

 

 

* The default setting is bold in the table below.

 

 

 

8 L-2 SELECT

 

Set this function to the appropriate mode depending on the

A/V:

To use this recorder as the recording

type of unit connected to the rear panel AV2 (L-2) IN/

 

deck with the player connected to

DECODER connector of the recorder.

 

the AV2 (L-2) IN/DECODER

NOTES:

 

connector, or to use the satellite

 

receiver connected to the AV2 (L-2)

If you have a decoder connected to the AV2 (L-2) IN/DECODER

 

IN/DECODER connector.

connector, be sure to set “L-2 SELECT” back to “DECODER”

DECODER:

after editing.

To use a decoder connected to the

If you’re not connecting a decoder to the AV2 (L-2) IN/

 

AV2 (L-2) IN/DECODER connector.

SAT:

DECODER connector, leave “L-2 SELECT” set to “A/V”.

To view a satellite programme with

The default setting is “A/V”; if the recorder’s memory backup has

 

the TV set while the recorder is

expired due to a power cut or because the AC was removed

 

turned off. ( pg. 31)

from the recorder, “A/V” will be automatically selected when

 

 

the power is restored to the recorder. If you are using a decoder,

 

 

be sure to set “L-2 SELECT” back to “DECODER”.

 

 

When “L-2 SELECT” is set to “SAT”, “SAT” or “SAt” appears on

 

 

the screen or front display panel instead of “L-2”.

 

 

8 COLOUR SYSTEM

You can play back PAL, NTSC and MESECAM tapes, or

PAL/NTSC:

To record PAL signals, or play back a

record PAL and SECAM* signals on this recorder. Select the

 

PAL or NTSC tape.

appropriate colour system.

MESECAM:

To record SECAM signals, or play

* SECAM signals will be recorded as MESECAM on this recorder;

 

back a MESECAM tape.

MESECAM is the designation for tapes with SECAM signals that

 

 

have been recorded on a MESECAM-compatible PAL video

 

 

cassette recorder.

 

 

NOTES:

 

 

About NTSC Playback

 

 

Some TVs shrink the picture vertically and place black bars at

 

 

the top and bottom of the TV screen. This is not a malfunction

 

 

on the part of either the video recorder or the TV.

 

 

The picture may roll up and down. This can be corrected using

 

 

the V-HOLD control found on some TVs. (This cannot be

 

 

corrected if the TV does not have a V-HOLD control.)

 

 

The counter and tape remaining time readings will be incorrect.

 

 

During search, still, or frame-by-frame playback, the picture will

 

 

be distorted, and there may be a loss of colour.

 

 

Depending on the type of TV, the top and bottom portions of

 

 

superimposed displays may be cut off during NTSC playback.

 

 

 

Image 37
Contents Video Cassette Recorder English Safety Precautions Moisture Condensation Front View Front Display Panel ON-SCREEN Display Operating JVC TVs How To UseSituate the recorder Check the contentsConnect the recorder to TV Connect the recorder to mainsTurn on the recorder Auto Set UpSelect your country Before starting, make sure of the followingSelect the language Perform Auto Set UpOn the front display panel On the on-screen display10 EN Perform Preset DownloadSet the video channel Press rt to select CH - and press OK or eJust Clock Language for the on-screen displayAccess the Country Set screen Access the Main Menu screenLanguage 12 ENLink Functions NexTView Link TV Auto Power OnVCR Auto Standby Direct Rec14 EN Basic PlaybackHigh-Speed Search Slow MotionVariable Speed Search Pause during playbackManual Tracking 16 ENInstant ReView Skip Search Index SearchNext Function Memory Repeat Playback18 EN Engage the ITR mode Instant Timer Recording ITRWatching Another Set the recording duration20 EN Reset the counterTape Remaining Time Display the counterRecording PlaybackBefore performing the Showview Timer Programming Access the Showview screen22 EN Enter the Showview numberEngage the recorder’s timer mode Set the VPS/PDC modePress SP/LP p Press VPS/PDC to select on or OFF24 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR +Cancel or change a programme Check, cancel and change programmesReturn to the timer mode Disengage the timer modeConfirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Engage the Auto Satellite Programme Recording mode Select the L-2 Select modeProgramme Recording 28 ENEdit From a Camcorder Another Video Recorder Set the input mode of recording deck30 EN Start the source playerConnecting To a Satellite Receiver 32 EN Select the input modeConnect the decoder Set the tunerAccess the Initial Set screen Showview System SetupGuide Program Number Set Guide Program NumberAccess the Mode Set screen Mode SetSelect the mode Select the mode settingThis feature helps you to adjust the playback picture You can set the B.E.S.T. Biconditional Equalised SignalWhen this function is set to ON, the timer is Off, and automatically disengaged when the recorder isFor Example 36 ENAbout Ntsc Playback Tuner Set Access the Auto Channel Set screen38 EN Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice Manual Channel Set 40 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations a 42 ENSet Stations B Station Name TV Station And ID ListClock Set Access the Clock Set screen44 EN Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operationExit the Video Channel Set mode Access the Video Channel Set modeVideo Channel Set 46 ENPower Recording 48 ENOther Problems Playback 50 ENConnecting To a Satellite Receiver Auto Channel Set Auto Set UpTimer warning display Tuner Set Watching AnotherMonochrome signal, 625 lines Signal systemMemory backup time Approx min LP HR-J480EU only 480 min. with E-240 video cassette