JVC HR-J480EU specifications Programme Recording, 28 EN, Select the L-2 Select mode

Page 28

28 EN

TIMER RECORDING (cont.)

Automatic Satellite

Programme

Recording

This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the recorder and programme the timer on the satellite receiver. The recorder starts or stops recording by the signals input from the satellite receiver. After recording, the recorder’s power shuts off automatically.

SAT# indicator

ATTENTION

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver’s power is turned on.

●If you have connected another appliance other than a satellite receiver to the AV2 (L-2) IN/DECODER connector, be sure not to engage the Auto Satellite Programme Recording mode; otherwise, the recorder will start recording when the connected appliance’s power is turned on.

●Auto Satellite Programme Recording and timer-recording cannot be done at the same time.

Before performing the following steps:

●Make sure the satellite receiver is connected to the recorder’s AV2 (L-2) IN/DECODER connector. ( pg. 31)

●Programme the timer on the satellite receiver.

●Insert a cassette with the safety tab in place.

A Select the L-2 SELECT mode.

Set “L-2 SELECT” to “A/V” or “SAT” ( pg. 37).

●When you select “SAT”, refer to “IMPORTANT” on page 31.

B Set the tape speed. (HR-J480EU only)

Press SP/LP (p).

C Engage the Auto Satellite Programme

Recording mode.

Press and hold SAT# for about 2 seconds. The SAT# indicator lights up and the recorder turns off automatically.

NOTES:

●To disengage the Auto Satellite Programme Recording mode, press SAT#. The SAT# indicator goes off.

●If the recorder’s power is off, it is not possible to engage the Auto Satellite Programme Recording mode.

●In step 3, if the SAT# indicator does not light but instead blinks quickly even though your satellite receiver’s power is off, Auto

Satellite Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Express Timer Programming” ( pg. 24) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Auto Satellite Programme Recording is not possible with those satellite receivers.

●The SAT# indicator blinks while Auto Satellite Programme Recording is in progress.

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Auto Satellite Programme Recording is not possible if your satellite receiver does not have a timer.

●Pressing the recorder’s 1 button while Auto Satellite Programme Recording is in progress turns off the recorder’s power and disengages the Auto Satellite Programme Recording mode.

●If there are more than one satellite programmes you wish to record with Auto Satellite Programme Recording, it is not possible to set different tape speeds for each programme.

●Depending on the type of satellite receiver, the recorder may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Auto Satellite Programme Recording mode when the satellite receiver’s power is on, the recorder will not start Auto Satellite Programme Recording even though the SAT# indicator blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer.

●The B.E.S.T. system ( pg. 21) does not work while Auto Satellite Programme Recording is in progress.

●Just Clock ( pg. 44) does not work when the Auto Satellite Programme Recording mode is engaged.

●When the Auto Satellite Programme Recording mode is engaged, or the recorder’s power is turned off after Auto Satellite Programme Recording is finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON”.

●After Auto Satellite Programme Recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function ( pg. 16).

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Video Cassette Recorder English Safety Precautions Moisture Condensation Front View Front Display Panel ON-SCREEN Display How To Use Operating JVC TVsCheck the contents Situate the recorderConnect the recorder to TV Connect the recorder to mainsAuto Set Up Turn on the recorderSelect your country Before starting, make sure of the followingPerform Auto Set Up Select the languageOn the front display panel On the on-screen displayPerform Preset Download 10 ENSet the video channel Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockAccess the Main Menu screen Access the Country Set screenLanguage 12 ENNexTView Link TV Auto Power On Link FunctionsVCR Auto Standby Direct RecBasic Playback 14 ENSlow Motion High-Speed SearchVariable Speed Search Pause during playbackManual Tracking 16 ENInstant ReView Index Search Skip SearchNext Function Memory Repeat Playback18 EN Instant Timer Recording ITR Engage the ITR modeWatching Another Set the recording durationReset the counter 20 ENTape Remaining Time Display the counterPlayback RecordingAccess the Showview screen Before performing the Showview Timer Programming22 EN Enter the Showview numberSet the VPS/PDC mode Engage the recorder’s timer modePress SP/LP p Press VPS/PDC to select on or OFFExpress Timer Programming 24 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the channel position Press PR +Check, cancel and change programmes Cancel or change a programmeReturn to the timer mode Disengage the timer modeConfirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Select the L-2 Select mode Engage the Auto Satellite Programme Recording modeProgramme Recording 28 ENEdit From a Camcorder Set the input mode of recording deck Another Video Recorder30 EN Start the source playerConnecting To a Satellite Receiver Select the input mode 32 ENConnect the decoder Set the tunerShowview System Setup Access the Initial Set screenGuide Program Number Set Guide Program NumberMode Set Access the Mode Set screenSelect the mode Select the mode settingYou can set the B.E.S.T. Biconditional Equalised Signal This feature helps you to adjust the playback pictureWhen this function is set to ON, the timer is Off, and automatically disengaged when the recorder is36 EN For ExampleAbout Ntsc Playback Access the Auto Channel Set screen Tuner Set38 EN Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice 40 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations a 42 ENSet Stations B TV Station And ID List Station NameClock Set Access the Clock Set screen44 EN Set the date and time Set Just ClockSet the source channel position for clock data Start the clock operationAccess the Video Channel Set mode Exit the Video Channel Set modeVideo Channel Set 46 ENPower 48 EN RecordingOther Problems 50 EN PlaybackAuto Channel Set Auto Set Up Connecting To a Satellite ReceiverTimer warning display Tuner Set Watching AnotherSignal system Monochrome signal, 625 linesMemory backup time Approx min LP HR-J480EU only 480 min. with E-240 video cassette
Top Page Image Contents