JVC HR-J480EU, HR-J280EU, HR-J281EU, HR-J289EU specifications 36 EN, For Example

Page 36

36 EN

 

SUBSIDIARY SETTINGS (cont.)

 

 

* The default setting is bold in the table below.

 

 

 

 

 

8 AUTO SP]LP TIMER

 

When this function is set to “ON”, the recorder

(HR-J480EU only)

 

automatically switches to LP mode to allow complete

ON

 

recording if there is not enough tape to record the entire

OFF

 

programme while timer-recording in SP mode.

 

 

For Example . . .

 

 

 

 

Recording a programme of 210 minutes in length onto a

 

 

180-minute tape

 

 

 

 

Approximately 150 minutes

Approximately 60 minutes

 

 

 

 

 

 

 

SP mode

LP mode

 

 

 

 

 

 

 

 

Total 210

minutes

 

 

 

Make sure you set this function to “ON”, before the

 

 

timer-recording starts.

 

 

 

 

NOTES:

 

 

 

 

If you have programmed the recorder to timer-record 2 or more

 

 

programmes, the second programme and those thereafter may

 

 

not fit on the tape if you set “AUTO SP]LP TIMER” to “ON”. In

 

 

this case, make sure the mode is not engaged, then set the tape

 

 

speed manually during timer programming.

 

 

In order to ensure that the recording fits on the tape, this feature

 

 

may leave a slight non-recorded section at the end of the tape.

 

 

There may be some noise and sound disturbance at the point on

 

 

the tape where the recorder switches from SP to LP mode.

 

 

The Auto SP]LP Timer feature is not available during ITR

 

 

(Instant Timer Recording), and the feature will not work properly

 

 

with any tapes longer than E-180, or with some tapes of shorter

 

 

lengths.

 

 

 

 

If you perform timer recording with both VPS/PDC and the Auto

 

 

SP]LP Timer activated, and the programme goes beyond its

 

 

originally scheduled length, there may be times when the

 

 

programme cannot be recorded in its entirety.

 

 

 

 

 

8 POWER SAVE

 

When this function is set to “ON”, you can reduce the

ON

 

power consumption while the recorder is turned off.

OFF

 

NOTES:

 

 

 

 

 

 

 

 

During Power Save mode ...

 

 

 

 

... the front display panel will be turned off.

 

 

... the Just Clock function ( pg. 44) does not work.

 

 

... the picture may be distorted momentarily when you turn on/

 

 

off the recorder.

 

 

 

 

Power Save does not work when ...

 

 

... the recorder is in the Timer mode.

 

 

... the recorder’s power is turned off after timer-recording or

 

 

Instant Timer Recording.

 

 

 

 

... the Auto Satellite Programme Recording mode is engaged

 

 

( pg. 28).

 

 

 

 

... “L-2 SELECT” is set to “DECODER” or “SAT” ( pg. 37).

 

 

 

 

 

Image 36
Contents Video Cassette Recorder English Safety Precautions Moisture Condensation Front View Front Display Panel ON-SCREEN Display How To Use Operating JVC TVsCheck the contents Situate the recorderConnect the recorder to TV Connect the recorder to mainsAuto Set Up Turn on the recorderSelect your country Before starting, make sure of the followingPerform Auto Set Up Select the languageOn the front display panel On the on-screen displayPerform Preset Download 10 ENSet the video channel Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockAccess the Main Menu screen Access the Country Set screenLanguage 12 ENNexTView Link TV Auto Power On Link FunctionsVCR Auto Standby Direct RecBasic Playback 14 ENSlow Motion High-Speed SearchVariable Speed Search Pause during playback16 EN Manual TrackingInstant ReView Index Search Skip SearchNext Function Memory Repeat Playback18 EN Instant Timer Recording ITR Engage the ITR modeWatching Another Set the recording durationReset the counter 20 ENTape Remaining Time Display the counterPlayback RecordingAccess the Showview screen Before performing the Showview Timer Programming22 EN Enter the Showview numberSet the VPS/PDC mode Engage the recorder’s timer modePress SP/LP p Press VPS/PDC to select on or OFFExpress Timer Programming 24 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the channel position Press PR +Check, cancel and change programmes Cancel or change a programmeReturn to the timer mode Disengage the timer modeCancel or change programme setting Confirm the overlapping programmesSelect the programme to modify Select the L-2 Select mode Engage the Auto Satellite Programme Recording modeProgramme Recording 28 ENEdit From a Camcorder Set the input mode of recording deck Another Video Recorder30 EN Start the source playerConnecting To a Satellite Receiver Select the input mode 32 ENConnect the decoder Set the tunerShowview System Setup Access the Initial Set screenGuide Program Number Set Guide Program NumberMode Set Access the Mode Set screenSelect the mode Select the mode settingYou can set the B.E.S.T. Biconditional Equalised Signal This feature helps you to adjust the playback pictureWhen this function is set to ON, the timer is Off, and automatically disengaged when the recorder is36 EN For ExampleAbout Ntsc Playback Access the Auto Channel Set screen Tuner Set38 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice 40 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a Channel42 EN Set Stations aSet Stations B TV Station And ID List Station NameAccess the Clock Set screen Clock Set44 EN Set the date and time Set Just ClockSet the source channel position for clock data Start the clock operationAccess the Video Channel Set mode Exit the Video Channel Set modeVideo Channel Set 46 ENPower 48 EN RecordingOther Problems 50 EN PlaybackAuto Channel Set Auto Set Up Connecting To a Satellite ReceiverTimer warning display Tuner Set Watching AnotherSignal system Monochrome signal, 625 linesMemory backup time Approx min LP HR-J480EU only 480 min. with E-240 video cassette