JVC HR-J480EU 46 EN, Access the Video Channel Set mode, Set the RF output system

Page 46

46 EN

SUBSIDIARY SETTINGS (cont.)

Video Channel Set

Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the recorder through the RF cable.

IMPORTANT

Perform the following steps only if —

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV connection, or vice versa.

If you have connected the recorder to your TV via the AV connection ( pg. 7), since you do not need the video channel you have to set the video channel to off.

If you have connected the recorder to your TV via the RF connection ( pg. 7), you have to set the correct video channel.

Before performing the following steps:

Make sure the recorder’s power is off and there is no cassette inserted in the recorder.

A Access the Video Channel Set mode.

Hold down 0 on the recorder until the front display panel shows the following.

B Set the RF output system.

The blinking number on the display indicates the RF output system of your country.

●If you have selected MAGYARORSZÁG, CESKÁ REPUBLIKA,

POLSKA or OTHER EASTERN EUROPE for the country setting ( pg. 8, 12), press rt to set to “2”.

●For other countries, set to “1”. Then press OK. (1: B/G 2: D/K)

Then set your TV to UHF channel 50.

●If the two vertical white bars appear clearly on the TV screen as shown to the right, go to step 4.

●If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.

NOTES:

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

D Exit the Video Channel Set mode.

Press OK on the remote control.

C Set the video channel.

With AV Connection

Press PR – until the front display panel shows “1 – –” (or “2 – –”).

●Now the video channel is set to off.

With AV Connection

To view picture signals from the video recorder, set your TV to its AV mode.

With RF Connection

The channel on which the TV screen in step 3 appears clearly is your video channel.

To view picture signals from the video recorder, set your TV to the video channel.

With RF Connection

Press PR + or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area.

(Example) If channel 50 is available in your area

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Video Cassette Recorder English Safety Precautions Moisture Condensation Front View Front Display Panel ON-SCREEN Display How To Use Operating JVC TVsConnect the recorder to TV Check the contentsSituate the recorder Connect the recorder to mainsSelect your country Auto Set UpTurn on the recorder Before starting, make sure of the followingOn the front display panel Perform Auto Set UpSelect the language On the on-screen displaySet the video channel Perform Preset Download10 EN Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 12 ENVCR Auto Standby NexTView Link TV Auto Power OnLink Functions Direct RecBasic Playback 14 ENVariable Speed Search Slow MotionHigh-Speed Search Pause during playbackManual Tracking 16 ENInstant ReView Next Function Memory Index SearchSkip Search Repeat Playback18 EN Watching Another Instant Timer Recording ITREngage the ITR mode Set the recording durationTape Remaining Time Reset the counter20 EN Display the counterPlayback Recording22 EN Access the Showview screenBefore performing the Showview Timer Programming Enter the Showview numberPress SP/LP p Set the VPS/PDC modeEngage the recorder’s timer mode Press VPS/PDC to select on or OFFExpress Timer Programming 24 ENEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Press PR +Return to the timer mode Check, cancel and change programmesCancel or change a programme Disengage the timer modeConfirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Programme Recording Select the L-2 Select modeEngage the Auto Satellite Programme Recording mode 28 ENEdit From a Camcorder 30 EN Set the input mode of recording deckAnother Video Recorder Start the source playerConnecting To a Satellite Receiver Connect the decoder Select the input mode32 EN Set the tunerGuide Program Number Set Showview System SetupAccess the Initial Set screen Guide Program NumberSelect the mode Mode SetAccess the Mode Set screen Select the mode settingWhen this function is set to ON, the timer is You can set the B.E.S.T. Biconditional Equalised SignalThis feature helps you to adjust the playback picture Off, and automatically disengaged when the recorder is36 EN For ExampleAbout Ntsc Playback 38 EN Access the Auto Channel Set screenTuner Set Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice 40 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations a 42 ENSet Stations B TV Station And ID List Station NameClock Set Access the Clock Set screen44 EN Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode 46 ENPower 48 EN RecordingOther Problems 50 EN PlaybackTimer warning display Tuner Set Auto Channel Set Auto Set UpConnecting To a Satellite Receiver Watching AnotherMemory backup time Approx min Signal systemMonochrome signal, 625 lines LP HR-J480EU only 480 min. with E-240 video cassette
Top Page Image Contents