JVC HR-J631T manual CHECK/CORRECT Input Data, Engage Timer Mode

Page 29

OK	MENU

	1		2	3
NUMBER	4		5	6
NUMBER
	7		8	9
		K	0	TIMER
			0

CHECK/CORRECT INPUT

DATA

6 If the data is correct as it is, go to step 7. If not, press OK or PUSH JOG ª£ until the item you want to change begins to blink. Then press the appropriate NUMBER keys or CH5° to obtain the desired setting.

	RETURN TO NORMAL
7	SCREEN
	Press MENU as many times as necessary.

	● Press just once to access the Auto Timer screen
	(☞ pg. 34).

8	ENGAGE TIMER MODE
8	Press TIMER. The VCR turns off automatically.

NOTES:

●To disengage the timer before recording starts, press TIMER again. Pressing once more re-engages it.

●In case of a power failure after programming, the VCR’s memory backup keeps your selections for 18 hours.

●Backup time becomes shorter as the unit's internal parts become old. When this occurs, please consult your nearby JVC dealer.

Image 29

Contents HR-J631T Do not place the VCR Dear CustomerContents Connect VCR to Power Source Check ContentsBasic Connections Situate VCRClock Tuner Perform Auto Channel SET Access AFC Screen Access Tuner SET ScreenStore Desired Channel Return to Normal ScreenAccess Main Menu Screen Code SetupInput Guide Channel Number Access G-CODE SET-UP ScreenAccess Guide Channel SET Screen Return to Normal Return to G-CODE SET UP ScreenNumber Load a Cassette Simple PlaybackFind Program Start Point Start PlaybackSimple Recording Activate FRAME-BY Frame Playback Pause During PlaybackPlayb a CK and Recording Feat Ures Still Picture/Frame-By- Frame PlaybackActivate HIGH-SPEED Search Activate VARIABLE-SPEED SearchVariable-Speed Search Reverse Play High-Speed SearchAdjust Manual Tracking ModeEngage Manual TrackingMix Access Function SETSelect The Soundtrack Superimpose Playback and Recording FeaturesSkip Over Unwanted Sections Access Distant CodeStart Repeat Stop RepeatActivate Counter Activate Instant ReviewMemory Return to Counter Position ZeroRelation to B Beginning or E End shows you where you are on Tape Position IndicatorPress REW, then press Timer within 2 seconds Next-Function MemoryPicture System Preparation Select ModePress and hold REC RecordingQuality of the tape Use, then recording Begins with the picture Level optimizedTape in use PlaybackBefore beginning, perform steps 1 and 2 on Reset Counter to Zero Engage TV ModeRecording Select Channel for ViewingStereo And SAP Second Audio Program Access 2ND AudioTo Record SAP Programs To Record Stereo ProgramsEngage ITR Mode Instant Timer Recording ITRTimer Recording SET Recording DurationAccess G-CODE Screen Code Timer ProgrammingEnter G-CODE Number Check Input DataPress just once to access the Auto Timer screen Engage Timer ModePress TIMER. The VCR turns off automatically CHECK/CORRECT Input DataSelect Program On-Screen Timer ProgrammingSET Program InformationRecord a show on September If you program the VCR to timerOn channel 40 from 1200 noon To 100 PM in SP mode,Access Program SET Screen Disengage TimerCancel a Program RE-ENGAGE TimerPlace the arrow next to your choice on or OFF by press CH5 Access Function SET ScreenAuto SP/EP Timer Auto Timer Access Auto TimerTurn on the TV SET Remote ControlMode SET TV Brand CodeAccess AUX Input Screen SET RECORDER’S Input ModeEdit From a Camcorder Make ConnectionsStart Recorder Start PlayerLoad Cassettes Edit To Or From AnotherControl Two JVC VCRs Player Your VCRLocate Start Point SET Input ModeEngage Audio Dubbing Start DubbingMake sure the window side is up, Remote control won’t function Batteries are dischargedCassette gets stuck partway Re-perform the G-Code setup Doesn’t work properly Timer againPlayback Questions and AnswersSpeci Fications EIA monochrome signal20C to 60C -4F to140F Maximum recording timeIndex Front ViewFront Display Panel Remote Control ProvidedHR-J631T

MENU

CHECK/CORRECT INPUT

DATA

RETURN TO NORMAL

● Press just once to access the Auto Timer screen

ENGAGE TIMER MODE

Press TIMER. The VCR turns off automatically.