JVC HR-J631T manual Turn on the TV, SET Remote Control, Mode, SET TV Brand Code, Operate TV

Page 35

SPECIALFEATURES

35

TV/VIDEO
	1	2	3
NUMBER	4	5	6
NUMBER
	7	8	9
		0

VOL. +/-

STOP

POWER

ENTER

TV/VCR

TV Multi-Brand Remote Control

The VCR's remote control can control several functions on JVC remote control TVs and on the brands of remote control TVs listed below. Some TV brands have more than one code. If the TV will not function with one code, try entering another.

	TURN ON THE TV
1 Turn the power on using the TV's remote control.
	SET REMOTE CONTROL
2	MODE
	Set the TV/VCR switch on the VCR's remote control to
	TV.
	SET TV BRAND CODE
	Refer to the chart below. While holding down POWER,
	enter your TV’s brand code using the NUMBER keys,
3 then press STOP.
	● Once you have set the remote control to operate the
	TV, you don’t have to repeat this step until you
	replace your remote control’s batteries.

OPERATE TV

4 First, press POWER on the remote to see if the TV’s power goes off as it should. If it does, try other operations.

TV BRAND NAME	BRAND CODE
JVC	01
PHILIPS	03
HITACHI	05
SHARP	06
TOSHIBA	07
MITSUBISHI	08
DAEWOO	09, 10
SAMSUNG	11
GOLDSTAR	12
RCA	14
PANASONIC	15, 16
SONY	18

●The POWER, TV/VIDEO, CH5°, VOL +/– and NUMBER keys on the remote can all be used to operate the TV. *For some brands of TV, you must press ENTER after having pressed the NUMBER keys.

●To return the remote to VCR control, set the TV/VCR switch to VCR.

NOTE:

Depending on the kind of TV, there may be cases where some or all functions cannot be operated using the remote control.

Image 35

Contents HR-J631T Do not place the VCR Dear CustomerContents Situate VCR Check ContentsConnect VCR to Power Source Basic ConnectionsClock Tuner Perform Auto Channel SET Return to Normal Screen Access Tuner SET ScreenAccess AFC Screen Store Desired ChannelAccess Main Menu Screen Code SetupInput Guide Channel Number Access G-CODE SET-UP ScreenAccess Guide Channel SET Screen Return to Normal Return to G-CODE SET UP ScreenNumber Start Playback Simple PlaybackLoad a Cassette Find Program Start PointSimple Recording Still Picture/Frame-By- Frame Playback Pause During PlaybackActivate FRAME-BY Frame Playback Playb a CK and Recording Feat UresHigh-Speed Search Activate VARIABLE-SPEED SearchActivate HIGH-SPEED Search Variable-Speed Search Reverse PlayTracking Tracking ModeAdjust Manual Engage ManualMix Access Function SETSelect The Soundtrack Superimpose Playback and Recording FeaturesStop Repeat Access Distant CodeSkip Over Unwanted Sections Start RepeatReturn to Counter Position Zero Activate Instant ReviewActivate Counter MemoryNext-Function Memory Tape Position IndicatorRelation to B Beginning or E End shows you where you are on Press REW, then press Timer within 2 secondsPicture System Preparation Select ModeBegins with the picture Level optimized RecordingPress and hold REC Quality of the tape Use, then recordingTape in use PlaybackBefore beginning, perform steps 1 and 2 on Select Channel for Viewing Engage TV ModeReset Counter to Zero RecordingTo Record Stereo Programs Access 2ND AudioStereo And SAP Second Audio Program To Record SAP ProgramsSET Recording Duration Instant Timer Recording ITREngage ITR Mode Timer RecordingCheck Input Data Code Timer ProgrammingAccess G-CODE Screen Enter G-CODE NumberCHECK/CORRECT Input Data Engage Timer ModePress just once to access the Auto Timer screen Press TIMER. The VCR turns off automaticallyInformation On-Screen Timer ProgrammingSelect Program SET ProgramTo 100 PM in SP mode, If you program the VCR to timerRecord a show on September On channel 40 from 1200 noonRE-ENGAGE Timer Disengage TimerAccess Program SET Screen Cancel a ProgramPlace the arrow next to your choice on or OFF by press CH5 Access Function SET ScreenAuto SP/EP Timer Auto Timer Access Auto TimerSET TV Brand Code SET Remote ControlTurn on the TV ModeMake Connections SET RECORDER’S Input ModeAccess AUX Input Screen Edit From a CamcorderStart Recorder Start PlayerPlayer Your VCR Edit To Or From AnotherLoad Cassettes Control Two JVC VCRsStart Dubbing SET Input ModeLocate Start Point Engage Audio DubbingMake sure the window side is up, Remote control won’t function Batteries are dischargedCassette gets stuck partway Re-perform the G-Code setup Doesn’t work properly Timer againPlayback Questions and AnswersMaximum recording time EIA monochrome signalSpeci Fications 20C to 60C -4F to140FIndex Front ViewFront Display Panel Remote Control ProvidedHR-J631T