JVC HR-J631T manual Access Function SET Screen, Auto SP/EP Timer

Page 33

OK

CH

MENU

6

q

33

Auto SP/EP Timer

If, when recording in SP mode, there is not enough tape to record the entire program, the VCR automatically switches to EP mode to allow complete recording. This feature is especially handy when recording a program of more than 2 hours in length.

For Example . . .

Recording a program of 140 minutes in length onto a 120- minute tape

Approximately 110 minutes	Approximately 30 minutes

SP mode	EP mode

Total 140 minutes

Make sure you select “ON” at the Auto SP/EP Timer screen before performing timer programming.

1 2 3

4	5	6
7	8	9
	0	OK
	0

MENU

CH

1

2

3

ACCESS MAIN MENU SCREEN

Press MENU as many times as necessary.

ACCESS FUNCTION SET SCREEN

Place the arrow next to "FUNCTION SET" by pressing CH5°, then press OK.

ACCESS AUTO SP/EP TIMER SCREEN

Place the arrow next to “AUTO SP/EP TIMER” by pressing CH5°, then press OK.

4

SELECT MODE

Place the arrow next to your choice (“ON” or “OFF”) by press CH5°.

AUTO SP/EP TIMER

=ON

OFF

PRESS (5,°) TO SELECT

PRESS (MENU) TO END

NOTES:

●If you have programmed the VCR to timer-record 2 or more programs, the second program and those thereafter may not fit on the tape if you set the Auto SP/EP Timer mode to "ON". In this case, make sure the mode is not engaged, then set the tape speed manually during timer programming.

●There may be some noise at the point on the tape where the VCR switches from SP to EP mode.

●The Auto SP/EP Timer feature is not available during ITR (Instant Timer Recording), and the feature will not work properly with any tapes other than the following: T-30, T-60, T-90, and T-120.

5

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

Image 33

Contents HR-J631T Do not place the VCR Dear CustomerContents Connect VCR to Power Source Check ContentsBasic Connections Situate VCRClock Tuner Perform Auto Channel SET Access AFC Screen Access Tuner SET ScreenStore Desired Channel Return to Normal ScreenAccess Main Menu Screen Code SetupAccess G-CODE SET-UP Screen Access Guide Channel SET ScreenInput Guide Channel Number Return to G-CODE SET UP Screen NumberReturn to Normal Load a Cassette Simple PlaybackFind Program Start Point Start PlaybackSimple Recording Activate FRAME-BY Frame Playback Pause During PlaybackPlayb a CK and Recording Feat Ures Still Picture/Frame-By- Frame PlaybackActivate HIGH-SPEED Search Activate VARIABLE-SPEED SearchVariable-Speed Search Reverse Play High-Speed SearchAdjust Manual Tracking ModeEngage Manual TrackingAccess Function SET Select The SoundtrackMix Superimpose Playback and Recording FeaturesSkip Over Unwanted Sections Access Distant CodeStart Repeat Stop RepeatActivate Counter Activate Instant ReviewMemory Return to Counter Position ZeroRelation to B Beginning or E End shows you where you are on Tape Position IndicatorPress REW, then press Timer within 2 seconds Next-Function MemoryPicture System Preparation Select ModePress and hold REC RecordingQuality of the tape Use, then recording Begins with the picture Level optimizedPlayback Before beginning, perform steps 1 and 2 onTape in use Reset Counter to Zero Engage TV ModeRecording Select Channel for ViewingStereo And SAP Second Audio Program Access 2ND AudioTo Record SAP Programs To Record Stereo ProgramsEngage ITR Mode Instant Timer Recording ITRTimer Recording SET Recording DurationAccess G-CODE Screen Code Timer ProgrammingEnter G-CODE Number Check Input DataPress just once to access the Auto Timer screen Engage Timer ModePress TIMER. The VCR turns off automatically CHECK/CORRECT Input DataSelect Program On-Screen Timer ProgrammingSET Program InformationRecord a show on September If you program the VCR to timerOn channel 40 from 1200 noon To 100 PM in SP mode,Access Program SET Screen Disengage TimerCancel a Program RE-ENGAGE TimerAccess Function SET Screen Auto SP/EP TimerPlace the arrow next to your choice on or OFF by press CH5 Auto Timer Access Auto TimerTurn on the TV SET Remote ControlMode SET TV Brand CodeAccess AUX Input Screen SET RECORDER’S Input ModeEdit From a Camcorder Make ConnectionsStart Recorder Start PlayerLoad Cassettes Edit To Or From AnotherControl Two JVC VCRs Player Your VCRLocate Start Point SET Input ModeEngage Audio Dubbing Start DubbingRemote control won’t function Batteries are discharged Cassette gets stuck partwayMake sure the window side is up, Re-perform the G-Code setup Doesn’t work properly Timer againPlayback Questions and AnswersSpeci Fications EIA monochrome signal20C to 60C -4F to140F Maximum recording timeIndex Front ViewFront Display Panel Remote Control ProvidedHR-J631T