JVC HR-J631T manual Questions and Answers, Playback

Page 42

42QUESTIONSANDANSWERS

PLAYBACK

Q. What happens if the end of the tape is reached during playback or search?

A.The tape is automatically rewound to the beginning.

Q.Can the VCR indefinitely remain in the still mode?

A.No. It stops automatically after 5 minutes to protect the heads.

Q.During search, slow, still and frame-by-frame playback, I can’t hear any audio. What’s the problem?

A.This is normal.

Q.During search, still and frame-by-frame playback, the picture is intermittent. What’s the cause?

A.Picture loss occurs when these types of playback are attempted with a tape recorded in LP mode. Pressing PLAY to return to normal playback will restore the picture.

Q.When returning from multi-speed search to normal playback, the picture is disturbed. Should I be concerned about this?

A.No, it is normal.

Q.Noise bars appear during multi-speed search. What’s the problem?

A.This is normal.

Q.Other than preventing further recording, what effect does removing the safety tab have?

A.It disables marking of index codes.

Q.Sometimes, during Index Search, the VCR can’t find the program I want to see. Why not?

A.There may be index codes too close together.

Q.During playback, on-screen operational indicators sometimes jitter. Why does this happen?

A.If the condition of the tape being played back is not good, jittering of the video (including on-screen indicators) may occur.

RECORDING

Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the new recording. Why does this happen?

A. This is normal. It reduces distortion at the pause and resume points.

Q. Can the VCR indefinitely remain in the Record-Pause mode?

A.No. The VCR automatically goes to its Stop mode after 5 minutes to protect the heads. When paused during Instant Timer Recording (ITR), the VCR shuts off automatically after 5 minutes.

Q.What happens if the tape runs out during recording?

A.The VCR automatically rewinds it to the beginning.

TIMER RECORDING

Q. REC and TIMER remain lit on the front display panel. Is there a problem?

A.No. This is a normal condition for a timer recording in progress.

Q.Can I program the timer while I’m watching a tape or a TV broadcast?

A.You won’t see the picture as it is replaced by the on- screen menu, but the audio from the program or tape you’re viewing is present.

Image 42
Contents HR-J631T Dear Customer Do not place the VCRContents Basic Connections Check ContentsConnect VCR to Power Source Situate VCRClock Tuner Perform Auto Channel SET Store Desired Channel Access Tuner SET ScreenAccess AFC Screen Return to Normal ScreenCode Setup Access Main Menu ScreenAccess G-CODE SET-UP Screen Access Guide Channel SET ScreenInput Guide Channel Number Return to G-CODE SET UP Screen NumberReturn to Normal Find Program Start Point Simple PlaybackLoad a Cassette Start PlaybackSimple Recording Playb a CK and Recording Feat Ures Pause During PlaybackActivate FRAME-BY Frame Playback Still Picture/Frame-By- Frame PlaybackVariable-Speed Search Reverse Play Activate VARIABLE-SPEED SearchActivate HIGH-SPEED Search High-Speed SearchEngage Manual Tracking ModeAdjust Manual TrackingAccess Function SET Select The SoundtrackMix Playback and Recording Features SuperimposeStart Repeat Access Distant CodeSkip Over Unwanted Sections Stop RepeatMemory Activate Instant ReviewActivate Counter Return to Counter Position ZeroPress REW, then press Timer within 2 seconds Tape Position IndicatorRelation to B Beginning or E End shows you where you are on Next-Function MemorySelect Mode Picture System PreparationQuality of the tape Use, then recording RecordingPress and hold REC Begins with the picture Level optimizedPlayback Before beginning, perform steps 1 and 2 onTape in use Recording Engage TV ModeReset Counter to Zero Select Channel for ViewingTo Record SAP Programs Access 2ND AudioStereo And SAP Second Audio Program To Record Stereo ProgramsTimer Recording Instant Timer Recording ITREngage ITR Mode SET Recording DurationEnter G-CODE Number Code Timer ProgrammingAccess G-CODE Screen Check Input DataPress TIMER. The VCR turns off automatically Engage Timer ModePress just once to access the Auto Timer screen CHECK/CORRECT Input DataSET Program On-Screen Timer ProgrammingSelect Program InformationOn channel 40 from 1200 noon If you program the VCR to timerRecord a show on September To 100 PM in SP mode,Cancel a Program Disengage TimerAccess Program SET Screen RE-ENGAGE TimerAccess Function SET Screen Auto SP/EP TimerPlace the arrow next to your choice on or OFF by press CH5 Access Auto Timer Auto TimerMode SET Remote ControlTurn on the TV SET TV Brand CodeEdit From a Camcorder SET RECORDER’S Input ModeAccess AUX Input Screen Make ConnectionsStart Player Start RecorderControl Two JVC VCRs Edit To Or From AnotherLoad Cassettes Player Your VCREngage Audio Dubbing SET Input ModeLocate Start Point Start DubbingRemote control won’t function Batteries are discharged Cassette gets stuck partwayMake sure the window side is up, Timer again Re-perform the G-Code setup Doesn’t work properlyQuestions and Answers Playback20C to 60C -4F to140F EIA monochrome signalSpeci Fications Maximum recording timeFront View IndexRemote Control Provided Front Display PanelHR-J631T