Kathrein UFD 345 manual Initial settings, Tuning in radio programmes, Radio menu

Page 19

Initial settings

Programme providers are continually bringing out new radio programmes for broadcast via the satellites. The “Radio“ menu allows you to store these pro- grammes.

The settings for radio programmes in “Radio“ mode are carried out in the same way as for the “TV“ mode.

Tuning in radio programmes

Switch from “TV mode“ into “Radio mode“ using the key.

First select the programme slot that is to be programmed afresh.

Call up the radio menu by pressing the + keys in succession.

Select the desired menu line using the keys.

For direct numeric input use the keys ...

or

Alter the values step-by-step with the keys.

Press the key twice in order to save your settings.

Exit from the menu with the key.

The “radio” menu

The following settings can be made in the radio menu:

 

 

Radio programme:

R 02

Sat frequency:

11214 MHz

Polarisation:

Hor. Low

Orbit position:

1

Deviation:

16 MHz

Oscillator:

LO 1

Mode:

STEREO

Frequency:

7.38/7.56 MHz

De-emphasis:

DNR/75μs

 

VOL 0-9 A/B STOR STBY

 

 

The bottom line shows the keys you can use to make the settings.

 

Radio programmes are transmitted on sound subcarriers only. The setting to be

 

made is therefore either “Stereo“ or “Mono narrow“. Here the audio de-emphasis is

 

selected automatically as “DNR“ and 75 μs.

Note

You can terminate any setup procedure immediately (also without storing) by re-

 

turning to normal operation via the

key.Grundeinstellungen

 

In the initial setup menu, matching of the satellite receiver to the satellite receiving

 

system is carried out.

 

Important

The receiver has already been factory pre-programmed for standard satellite re-

 

ceiving systems.

 

 

Alterations to the initial setting are therefore necessary only if your receiving sys-

 

tem deviates from this type of installation or if you happen to want different set-

 

tings.

 

The settings in the initial setup menu are generally carried out by the specialist dealer on installation of the satellite receiving system.

To prevent any unintentional alterations in the initial settings, the initial setup menu

19

Image 19
Contents Kathrein Satellite Receiver UFD Contents Controls, displays and connections Front panel Remote control handset keysRear panel connections Important notes regarding operation Safety instructionsImportant notes for siting and installation Power supply Connecting up and putting into operationInstalling the receiver Connecting up the unitReceiving system presets Satellite signal connectionTV and video recorder connection VCR Inserting batteries into remote control handsetDecoder connection Selecting a programme Switching the unit onSwitching between TV and radio mode Receiver operationMuting the sound Adjusting volume, balance and toneSAT/TV changeover Operating the receiver without remote controlStereo- / Mono- / Channel changeover Video recorder playback VCRDisplaying Info Displaying the Info menu and programme overviewProgramme overview Picture optimisation when reception is weakProgramming TV programmes Tuning in TV programmesVideo menu Orbit position Satellite frequencyPolarisation/Orbit position PolarisationProgramme name Decoder menuAudio de-emphasis for sound type Mono wide only Audio modeAudio menu Audio frequencyTuning in radio programmes Initial settingsRadio menu Calling the initial setup menu Programme selection OSD languageLNB supply voltage LNB supply voltage in standbyChanging the oscillator frequency Oscillator frequencyDiSEqC menu Settings in the DiSEqCDiSEqC KHz signalTone-burst and DiSEqC-signal Tone burstDiSEqC Repeat Switching over remote control’s command setRemote Features Specifications General Temperature rangeAccessories Scart socket assignmentsMenu structure Video- and Audio Setup MenuPossible setting Radio Setup MenuInitial Setup Menu Service note Connection example / Service notePage 9985.729/0,5/06.98/SKS/PF Subject to alterations