Kathrein UFD 345 manual Switching over remote control’s command set, DiSEqC Repeat, Remote

Page 25

Initial settings

Thus take into account the specifications of the DiSEqC matrices or get in touch with the installer of the receiving system..

DiSEqC Repeat

If “DiSEqC components” are cascaded in a satellite receiving system (several DiSEqC matrices are connected in series), the menu entry "DiSEqC Repeat" must be switched to "On"

Remote

The “Remote” setting in the “DiSEqC” menu entry is intended for future applica- tions.

If the UFD 345 receiver is operated in a receiving system with a “Subscriber- controlled preprocessing system“ e.g. “Kathrein UFO mini digital”, Remote must be set in the DiSEqC menu.

In this case, the corresponding transmission frequency is selected in menu entry “Remote Frequency” in the range 920 to 2150 MHz. The satellite signal is trans- mitted from the receiving system to the receiver on this frequency.

Press the key twice to save your settings.

Exit from the initial setup menu with the key (press twice).

Note

If you exit the menus without saving, the settings will be lost.

Switching over remote control’s command set

The remote control handset contains two command sets. This allows two receivers of the 200/300 series to be operated independently in a room (not in conjunction with a twin receiver).

For this purpose, programme one receiver on command set 1 and the second re- ceiver on command set 2.

Switch on receiver 1 and switch off receiver 2 (with the mains switch on the unit or interrupt the power supply).

Press the key and keep it pressed.

Using the numeric keys enter “001”.

Switch receiver 1 off (with the mains switch on the unit or interrupt the power supply) and switch receiver 2 on.

Press the key and keep it pressed.

Using the numeric keys enter “002”.

Switch receiver 1 on once again.

Press the key and keep it pressed.

Using the numeric keys enter “003”.

Note

With the first two settings the remote control must be pointed towards the respec-

 

tive receiver which is switched on.

 

With the

key you can now switch between the two command sets A and B

 

(toggle function) and operate the two receivers in alternation.

 

On delivery command set 1 is always active.

Note

If you are using only one receiver and the active command set has been switched

 

over inadvertently due to maloperation rendering the receiver inoperable, the re-

 

mote control can be switched back to command set 1 without difficulty. The proce-

 

dure for this has already been described above.

25

Image 25
Contents Kathrein Satellite Receiver UFD Contents Controls, displays and connections Front panel Remote control handset keysRear panel connections Important notes regarding operation Safety instructionsImportant notes for siting and installation Installing the receiver Connecting up and putting into operationConnecting up the unit Power supplyReceiving system presets Satellite signal connectionTV and video recorder connection VCR Inserting batteries into remote control handsetDecoder connection Switching between TV and radio mode Switching the unit onReceiver operation Selecting a programmeMuting the sound Adjusting volume, balance and toneStereo- / Mono- / Channel changeover Operating the receiver without remote controlVideo recorder playback VCR SAT/TV changeoverDisplaying Info Displaying the Info menu and programme overviewProgramme overview Picture optimisation when reception is weakProgramming TV programmes Tuning in TV programmesVideo menu Polarisation/Orbit position Satellite frequencyPolarisation Orbit positionProgramme name Decoder menuAudio menu Audio modeAudio frequency Audio de-emphasis for sound type Mono wide onlyTuning in radio programmes Initial settingsRadio menu Calling the initial setup menu LNB supply voltage OSD languageLNB supply voltage in standby Programme selectionChanging the oscillator frequency Oscillator frequencyDiSEqC menu Settings in the DiSEqCTone-burst and DiSEqC-signal KHz signalTone burst DiSEqCDiSEqC Repeat Switching over remote control’s command setRemote Features Specifications Accessories Temperature rangeScart socket assignments GeneralMenu structure Video- and Audio Setup MenuPossible setting Radio Setup MenuInitial Setup Menu Service note Connection example / Service notePage 9985.729/0,5/06.98/SKS/PF Subject to alterations