NetComm NP3640 manual Diagnostic Push Button, LED Indicators, Green LED Red LED Description

Page 5

Diagnostic Push Button

The Print Server is fitted with a Diagnostic Push Button. The button is recessed; a pin or paper clip can be used to press it. This button has 2 functions:

■Restore the factory default settings

■Print a test page containing all current settings. To restore the factory default settings:

1.Turn the Print Server OFF.

2.Press and hold the diagnostic button. While pressing the button, switch the Print Server ON.

3.If you continue pressing the button for 10 seconds, a diagnostic page will be printed, showing the new (default) settings.

To generate a Diagnostic print out

1.Ensure that both the Print Server and the printer attached to port 1 are ON.

2.Press the diagnostic button, and hold it in for 2 seconds.

3.The test page, containing the current settings, will be printed.

Note: PostScript printers are unable to print this page. If you have a PostScript printer on Port 1, the test page will not be printed.

LED Indicators

The Mini Print Server has four LED indicators; status, error, 10 BaseT and 100BaseT. The LED indicator modes are described in the following table:

Green LED	Red LED	Description
Off	Off	No power.
Off	On	Printer not on.
On	On	Hardware error.
Flashing	Flashing	Firmware upgrade in progress.
On	Off	Normal operation.
Flashing	Off	Normal operation - transmitting or receiving packets
		from the network.
Yellow LED	Orange LED	Description
On	Off	Connected at 10BaseT.
Off	On	Connected at 100BaseT.

Rev. 1 - YML657	www.netcomm.com.au
NP3640 Fast Ethernet Mini Print Server User Guide	Page 5

Image 5

Contents Page Contents Introduction Connecting your Mini Print Server LED Indicators Diagnostic Push ButtonGreen LED Red LED Description Yellow LED Orange LED DescriptionConfiguration Methods Configuring your Mini Print ServerAdvanced Configuration and Management Web Based Configuration and ManagementProcedure Using the Windows WizardRev YML657 Rev YML657 NP3640 Fast Ethernet Mini Print Server User Guide Which printing method should I use? Configuring your ComputersPrinting Methods Checking your Network Protocols Windows Windows Peer-to-peer Printing Windows 2000/XP SetupRev YML657 NP3640 Fast Ethernet Mini Print Server User Guide Windows 9x/ME Setup Rev YML657 NP3640 Fast Ethernet Mini Print Server User Guide Management Advanced Port Options Windows SMB Printing Printing from MS-DOS Programs Capture SettingsWindows with Server-based Print Queues Choose Standard TCP/IP Port, then click New Port Windows LPR PrintingAdvanced Setup and Management AppleTalk SetupMacintosh AppleTalk PrintingMacintosh OS LPR printing SetupRequirements BiAdmin Management UtilityInstallation Rev YML657 NP3640 Fast Ethernet Mini Print Server User Guide Printer Status IconsDevice Status Wizard ConfigurationUpgrade Menus System Tab ConfigurationTCP/IP Tab AppleTalk Tab NetBEUI Tab Internet Printing Tab Logical Port Port TabPhysical Port NetWare Snmp Tab Preparation Web-Based ManagementServer Status Connecting to the Print ServerConfiguration Screens Configure Server AppleTalk NetBEUI Connection TCP/IPGeneral Remote Printer ModePrint Server Mode Rev YML657 Trap Receivers Snmp Simple Network Management ProtocolManagement Stations Logical Printers Internet Printing Internet Printing Protocol IPP Special FeaturesIPP Server Configuration IPP Client Configuration Windows 95/98/ME/2000/XP/NT IPP Client Setup Windows 95/98/Me/NT 4.0/XPInstalling from the CD-ROM Installing using IPPCLIENT.EXEChanging the IPP Port Settings IPP Client Setup Windows 2000/XP Using IPP Printers System Requirements Internet Mail PrintingMail Server Internet Print ServerUser Software Internet Mail Printing ConfigurationInstallation User Software Printing through the Internet Using the new PortChecking the Printer Driver Snmp Settings Configuring the Print Server for SnmpManagement Station Settings Trap Receiving Station SettingsFax TroubleshootingHardware & LAN Problems AppleTalk Macintosh Problem, perform the following steps Novell NetWare Windows Printing Problems Click OK to see the Print Port Configuration screen, as Rev YML657 NP3640 Fast Ethernet Mini Print Server User Guide Windows NT Server Network Server ConfigurationPreparing for TCP/IP Printing Adding a TCP/IP Remote PrinterEnter the appropriate logical printer number. e.g. L1 Setup Wizard Configuration Methods Bindery or NDSNovell NetWare Windows 2000 ServerConfiguration Data BiAdminOther Method GeneralCreating an Ndps Manager Object Setup for Ndps NetWareOverview Load Ndpsm Creating an Ndps Printer AgentUnix Systems Trademarks and NoticesRegistering your NetComm Product Warranty Registration Form Page Limitations of Warranty Product Warranty