Toshiba 27HL95 manual Blocking channels, Unlocking programs temporarily, Locking video inputs

Chapter 9: Using the Locks menu

Blocking channels

With the Channels Block feature, you can block specific channels. You will not be able to tune blocked channels unless you clear the setting first.

To block channels:

1. Press MENU and highlight the Locks menu icon.

Note: To exit the Locks menu, press MENU.

2.	Press z, which displays
	the PIN code entering
	screen.
		Locks
3.	Enter your four-digit PIN	Enable Rating Blocking		Off
		Edit Rating Limits
	code and press ENTER	Channels Block
	(see page 76 for details).	Input Lock		Off
		Front Panel Lock		Off
4.	Press z to highlight	Game Timer		Off
		New PIN Code
	Channels Block and then
	press ENTER.		Navigate Select	RTN Back EXIT Exit

5. Using the yz x • buttons, select the input that you want to

change the rating limits for (ANT1, ANT2, or Cable				Box if
connected) and press ENTER.
A list of the channels available for that input will be displayed
along with the call letters for each channel, if available.
6. Press yz to highlight the	Channels Block			ANT 1
channel you want to
			1	ANT 1
block, then press
		2		ANT 2
ENTER, which puts an			3	Cable Box
“×” in the box next to			4
		5
that channel.
			6
7. Repeat step 6 for other			7	Allow All
		8		Block All
channels you want to
			9	Cancel
block.
		10		Done

8.Highlight Done and press

ENTER.

To unblock individual channels:

In step 6 above, press yz to highlight the channel you want to unblock, and then press ENTER to remove the “X” from the box, and highlight Done, and then press ENTER.

To block all channels at once:

Highlight Block All in step 6 above, and then highlight Done, and then press ENTER.

To unblock all locked channels at once:

Highlight Allow All in step 6 above, and then highlight Done, and then press ENTER.

Channels Block		ANT 1
	1	ANT 1
	2	ANT 2
	3	Cable Box
	4
	5
	6
	7	Allow All
	8	Block All
	9	Cancel
	10	Done

Note: Channel blocking may not take effect if you have a cable box connected and use the cable box controls to change channels.

Unlocking programs temporarily

If you try to watch a TV program that exceeds the rating limits you set, the TV enters program lock mode. You can either unlock the program temporarily or select a non-locked program to watch.

To temporarily unlock the program:

1.Press MUTE.

2.Enter your four-digit PIN code and press ENTER. If the correct code is entered,

the program lock mode	Locks							Active
	Enter PIN code to temporaily un-
is released and the
					block.
normal picture appears.
			*	*		*	*
All locking is disabled
until the TV is turned		Cancel					Done
off, and will be enabled
when the TV is turned on again.

Locking video inputs

You can use the Input Lock feature to lock the video input sources (VIDEO 1, VIDEO 2, ColorStream HD, HDMI, PC) and channels 3 and 4. You will not be able to view the input sources or channels until you turn off the input lock.

To lock the video inputs:

1.Press MENU and highlight the Locks menu icon.

2.Press z to display the PIN code entering screen.

3.Enter your four-digit PIN code and press ENTER.

4.Press z to highlight Input Lock and press •.

5.Press yz to select the level of video input locking you prefer, as described below:

Video: Locks VIDEO 1,
VIDEO 2, ColorStream
HD, HDMI, and PC.	Locks
	Enable Rating Blocking		Off	Off
Video+: Locks	Edit Rating Limits			Video
	Channels Block			Video +
VIDEO 1, VIDEO 2,	Input Lock		Off
	Front Panel Lock		Off
ColorStream HD,	Game Timer		Off
HDMI, PC, and	New PIN Code
channels 3 and 4. Select		Navigate Select	RTN Back	EXIT Exit

Video+ if you use the

antenna terminal to play a video tape.

Off: Unlocks all video input sources.

6. Press ENTER.

Note: When a CableCARDª is inserted, Video+ will behave the same as Video lock.

78		Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.
#01E_076-079_27HL95	78	05.9.12, 10:57 PM
	Black

(E) 27HL95 *Web 213 : 276