Toshiba 50HP82 owner manual

Page 46

*1 Only when using a graphic accelerator board that is capable of displaying 852480.

*2 This signal is converted to a 1024 dots  640 lines signal.

*3 The picture is displayed in the original resolution.

*4 The aspect ratio is 5:4. This signal is converted to a 960 dots768 lines signal.

*5 Normally the RGB select mode suited for the input signals is set automatically. If the picture is not displayed properly, set the RGB mode suited for the input signals listed in the table above.

*6 Other screen modes (ZOOM and JUST) are available as well.

NOTE:

While the input signals comply with the resolution listed in the table above, you may have to adjust the position and size of the picture or the fine picture because of errors in synchronization of your computer.

When a 1280 dots  1024 lines signal or 1600 dots  1200 lines signal is input to the monitor, the picture will be compressed.

This monitor has a resolution of 1365 dots  768 lines. It is recommended that the input signal should be XGA, wide XGA, or equivalent.

With digital input some signals are not accepted.

The sync may be disturbed when a nonstandard signal other than the aforementioned is input.

If you are connecting a composite sync signal, use the HD terminal.

* “IBM PC/AT” and “XGA” are registered trademarks of International Business Machines, Inc. of the United States.

46

Image 46
Contents 50HP82 Precautions Important InformationTo avoid damage and prolong operating life Recommendations to avoid or minimize phosphor burn-inContents How to Attach Options to the Plasma Display Ventilation Requirements for enclosure mountingIntroduction Features you’ll enjoy includeContents of the Package Introduction to the 50HP82 Plasma DisplayPart Names and Function Front ViewVIDEO1, 2 Rear View/ Terminal BoardEXT Speaker L and R DVD1 / HD1Remote Controller 8Remote control signal transmitter Battery Installation and Replacement9Remote Jack Operating Range Using the wired remote control modeHandling the remote controller ApproxInstallation Personal computer with a digital RGB outputConnecting Your DVD Player Connecting Your PCConnecting Your VCR Connections with Equipment that has a Digital InterfaceExternal Speaker Connections Right LeftPin Assignments and Signal Levels for 15-pin RGB Analog Pin No Signal AnalogBasic Operations To check the remaining time To set the off timerTo cancel the off timer → 30 → 60 → 90 → 120 →Wide Operations When watching VCR’s or DVDWhen watching high definition video source Watching with a wide screen manual Picture Size setting When Picture Size is set to OFF Supported resolution Watching computer images with a wide screenShowing two pictures on the screen at the same time Operations in the Side-by-side modeMulti Window Operations Side-by-sideAdjusting the OSD controls Operations in the Picture-in-picture modeSelecting the input signals to be displayed To change the size of the sub screen, press the Zoom ButtonOSDOn Screen Display Controls Menu OperationsMain menu Sub menu Functions  Picture adjustment screen Picture Settings MenuAdjusting the picture  Adjusting the computer imageTo set to Theater Example Setting the Theater mode Types of picture modes Once the setting is completed Setting the color temperatureExample Setting 1 See chart at right  Setting the color temperatureAdjust the white balance using the  and  buttons Adjusting the color to the desired qualityExample Adjusting the White Balance  Adjusting the white balance NR Example Setting NR-3Reducing noise in the picture  Types of noise reductionExample Adjusting the bass Sound Settings MenuAdjusting the treble, bass and left/right balance  Sound settings menuExample Adjusting the vertical position in the normal mode Screen Settings MenuAdjusting the Position, Size, Fine Picture, Picture Adj  When Auto Picture is OFF Adjusting the Auto Picture Function Settings MenuSetting the on-screen display  Adjusting the position of the imageTo adjust the position Adjusting the position of the menu displayExample Adjusting the position of the menu display  Adjusting the position of the menu display Power management function Setting the power management for computer imagesExample Turning the power management function on  Power management settingsGreen POWER/STANDBY indicatorDescription Turning the picture back on Horizontal and vertical synchronizing Picture already onExample Adjusting the Gray Level Setting the picture to suit the movieSetting the gray level for the sides of the screen Example Setting the Cinema Mode to OFF When you adjust the RGB3 ADJ Setting RGB3 ADJExample Setting Example Setting PLE to LockSetting the time for Inverse Perform Steps 1-2 on Page 36, then Setting the time Setting the time for Screen Wiper To select on for the Working Time Set the length of time until the Screen Wiper mode starts Resetting to the default values To select on for Working Time Setting the BNC connectors Options Settings MenuSetting the allocation of the audio connectors Example Setting Audio 1 to VideoTo set the RGB select mode to Motion Setting a computer image to the correct RGB select screenExample Setting the RGB Select mode to Motion See page 45 for the details of the above settingsSetting the picture size for RGB input signals Setting high definition images to the suitable screen size HD Select modes  Language settings Setting the language for the menusExample Setting the menu display to Deutsch Information Menu Video signal formats Setting the video signal formatExample Setting the video signal format to 3.58 Ntsc To select 3.58 NtscComputer input signals supported by this system Table of Signals SupportedSupported resolution FrequencyPage Troubleshooting Symptom Checks RemedySpecifications FCC Statement MODEL50HP82 Your Responsibility How to Obtain Warranty ServicesCommercial Units For additional information, visit TACP’s web siteLimited One 1 Year Warranty on Parts and Labor For additional information, visit TCL’s web site02-06 7S800701