Toshiba 50HP82 owner manual How to Attach Options to the Plasma Display

Page 5

How to Attach Options to the Plasma Display

You can attach your optional mounts or stand to the plasma display in one of the following two ways:

•While it is upright. (See Drawing A)

•As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the screen face.

•This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall hanging bracket, Pedestal, etc.)

See page 6.

•For correct installation and mounting it is strongly recommended to use a trained, authorized TOSHIBA dealer.

Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer.

Product warranty does not cover damage caused by improper installation.

•Use only Listed Cart or Stand, or mounting kit or stand provided by manufacturer.

Drawing A

Drawing B

Ventilation Requirements for enclosure mounting

To allow heat to disperse, leave space between surrounding objects as shown on the diagram at right when installing.

	Wall
2" (50mm)	2" (50mm)	)
	52.8" (1340mm)	mm
	52.8" (1340mm)	(50
		(50	Wall
		2"	Wall
		2"
		34.2" (866mm)
		)	2" (50mm)
		2" (50mm
	5

Image 5

Contents 50HP82 Important Information PrecautionsRecommendations to avoid or minimize phosphor burn-in To avoid damage and prolong operating lifeContents Ventilation Requirements for enclosure mounting How to Attach Options to the Plasma DisplayContents of the Package Features you’ll enjoy includeIntroduction Introduction to the 50HP82 Plasma DisplayFront View Part Names and FunctionEXT Speaker L and R Rear View/ Terminal BoardVIDEO1, 2 DVD1 / HD1Remote Controller 9Remote Jack Battery Installation and Replacement8Remote control signal transmitter Handling the remote controller Using the wired remote control modeOperating Range ApproxPersonal computer with a digital RGB output InstallationConnecting Your VCR Connecting Your PCConnecting Your DVD Player Connections with Equipment that has a Digital InterfaceRight Left External Speaker ConnectionsPin No Signal Analog Pin Assignments and Signal Levels for 15-pin RGB AnalogBasic Operations To cancel the off timer To set the off timerTo check the remaining time → 30 → 60 → 90 → 120 →When watching high definition video source When watching VCR’s or DVDWide Operations Watching with a wide screen manual Supported resolution When Picture Size is set to OFF Picture Size setting Watching computer images with a wide screenMulti Window Operations Operations in the Side-by-side modeShowing two pictures on the screen at the same time Side-by-sideSelecting the input signals to be displayed Operations in the Picture-in-picture modeAdjusting the OSD controls To change the size of the sub screen, press the Zoom ButtonMenu Operations OSDOn Screen Display ControlsMain menu Sub menu Functions Adjusting the picture Picture Settings Menu Picture adjustment screen Adjusting the computer image Types of picture modes Example Setting the Theater modeTo set to Theater Example Setting 1 See chart at right Setting the color temperatureOnce the setting is completed Setting the color temperatureExample Adjusting the White Balance Adjusting the color to the desired qualityAdjust the white balance using the and buttons Adjusting the white balanceReducing noise in the picture Example Setting NR-3 NR Types of noise reductionAdjusting the treble, bass and left/right balance Sound Settings MenuExample Adjusting the bass Sound settings menuAdjusting the Position, Size, Fine Picture, Picture Adj Screen Settings MenuExample Adjusting the vertical position in the normal mode When Auto Picture is OFFSetting the on-screen display Function Settings Menu Adjusting the Auto Picture Adjusting the position of the imageExample Adjusting the position of the menu display Adjusting the position of the menu displayTo adjust the position Adjusting the position of the menu displayExample Turning the power management function on Setting the power management for computer images Power management function Power management settingsDescription Turning the picture back on POWER/STANDBY indicatorGreen Horizontal and vertical synchronizing Picture already onSetting the gray level for the sides of the screen Setting the picture to suit the movieExample Adjusting the Gray Level Example Setting the Cinema Mode to OFFExample Setting Setting RGB3 ADJ When you adjust the RGB3 ADJ Example Setting PLE to LockPerform Steps 1-2 on Page 36, then Setting the time for Inverse To select on for the Working Time Setting the time for Screen Wiper Setting the time To select on for Working Time Resetting to the default valuesSet the length of time until the Screen Wiper mode starts Setting the allocation of the audio connectors Options Settings MenuSetting the BNC connectors Example Setting Audio 1 to VideoExample Setting the RGB Select mode to Motion Setting a computer image to the correct RGB select screenTo set the RGB select mode to Motion See page 45 for the details of the above settings HD Select modes Setting high definition images to the suitable screen sizeSetting the picture size for RGB input signals Example Setting the menu display to Deutsch Setting the language for the menus Language settings Information MenuExample Setting the video signal format to 3.58 Ntsc Setting the video signal format Video signal formats To select 3.58 NtscSupported resolution Table of Signals SupportedComputer input signals supported by this system FrequencyPage Symptom Checks Remedy TroubleshootingSpecifications FCC Statement MODEL50HP82 Commercial Units How to Obtain Warranty ServicesYour Responsibility For additional information, visit TACP’s web siteFor additional information, visit TCL’s web site Limited One 1 Year Warranty on Parts and Labor02-06 7S800701