Onkyo USR-5RF instruction manual Programming Buttons, Programming control panel buttons

Page 23

Getting the Maximum out of it

2. Programming Buttons

You program the remote controller commands by transmitting infrared signals from your existing remote controls to the remote controller’s learning eye. To do this, place the remote controller and the device’s remote controller on a flat surface, 15 to 20 cm (6 to 8 inches) apart.

15 to 20 cm (6 to 8 inches)

The following buttons can be programmed: control panel buttons, Device menu items, direct- access buttons and Left/Right buttons.

You cannot program Home menu buttons directly. You need to program them by following the Device menu (see page 24).

The remote controller also offers empty control panel buttons you can program and label as existing buttons. They are only visible in Learn and Label mode and appear without label or with label (intended for a specific function). You will also see previously deleted buttons: you can restore them by reprogramming them or you can reuse them for other commands.

Programming control panel buttons

1.Navigate to the control panel buttons you want to program.

2.Switch to Learn mode by using the Mode button.

Additional empty buttons appear: they can be programmed and labeled as existing buttons.

3.Point the device’s original remote controller to the remote controller’s learning eye as shown (see above).

4.Tap the remote controller button you want to program.

The button starts blinking.

5.Press and hold the corresponding button on your device’s original remote controller.

If the remote controller has learned the command successfully, OK blinks on the remote controller icon. You can let go of the button you’re holding.

If the remote controller has not learned the command successfully, you hear a short buzz and FAIL appears on the remote controller icon.

6.Program all other buttons you want and relabel them as necessary (see page 25).

7.Return to Use mode by using the Mode button.

23

Image 23

Contents USR-5RF Care PrecautionsTable of contents Operate your components Quick StartInsert batteries Touch the screen to startQuick reference Quick referenceModes Quick referenceIntroduction Intelligent Remote ControllerDirect-access buttons Which Buttons Can Be Programmed? Left and Right buttonsTouchscreen buttons AA batteries Charging the Remote ControllerOptional recharging dock Define the Brand of Your Device Activate the remote controllerGetting Started Tap Next Defining brands by selectingSelect Yes to define the brand of the device to operate Select your brand from the list Navigate through the list of brandsSelect a code set from the list Tap Search Defining brands by searchingVia the Device menu Select a DeviceVia the Home menu Scrolling Using touchscreen buttonsSending commands Operate a DeviceIR commands Device pages Use the Left and Right button to adjust the setting Adjust the SettingsTouch and hold the remote controller icon for a few seconds Tap the button of the setting you want to adjustThird setup panel Second setup panelWorking with Modes Getting the Maximum out of itIntroduction Tap Tap the mode you want to useTo hide the Mode menu Programming control panel buttons Programming ButtonsMake sure the device tab is active Programming direct-access and Left/Right ButtonsProgramming device items Edit the label Labeling Buttons and Menu ItemsLabeling a button Complete instruction 4 to 6 Labeling a button on Labeling a menu itemMoving menu items Adding and Moving DevicesAdding devices Deleting a button or button function Delete and restoreDelete Tap the item you want to restore RestoreRecording macros Recording Macros and Setting TimersEditing macros Setting timersTap Create Timer Group or Create Macro Group Editing timersOrganizing macros and timers into groups Edit the timer Press the Left button to close the timerUsing the remote controller with Radio Frequency Tap RF Changing the remote controller’s RF IR SettingsSwitch to RF IR mode by using Mode button Changing the Extender ID Try the devices which you just changed the RF IR settingsPress the + and action buttons to change the Channel Switch back to RF IR modeSelect a device that is set with RF signals Choosing Another ChannelWith ChadEdit you can ChadEditSystem requirements General Problems Programming Problems TroubleshootingRecharging Problems How do I revert to the original configuration? Can I program a button to execute more than one command?How do I program source switching? How do I reset the Remote controller?Overview of Symbols Specifications Onkyo U.S.A. Corporation