Onkyo USR-5RF Programming device items, Programming direct-access and Left/Right Buttons

Page 24

Getting the Maximum out of it

Programming device items

Note:

When you program a command to a device item, this command is automatically assigned to the corresponding button in the Home menu.

1.Make sure the device tab is active.

The device tab is active when the name of a device is displayed.

2.Switch to Learn mode by using the Mode button.

3.Point the device’s original remote controller to the remote controller’s learning eye as described above.

4.Tap the device tab to open the Device menu.

5.Touch and hold either the remote controller’s Left or Right button and tap the device you want to program.

Even when you want to program the currently active device, you have to tap it in the Device menu.

The label device starts blinking on the remote controller icon.

6.Press and hold the button the remote controller has to learn on your device’s original remote controller.

If the remote controller has been input the command successfully, OK will blink on the display. You can release the button you’re holding.

If the remote controller has not learned the command successfully, you hear a short buzz and FAIL appears on the remote controller icon.

7.Program all other items you want and return to Use mode via the Mode button.

Programming direct-access and Left/Right Buttons

Direct-access and Left/Right buttons can be programmed with a global function or with functions per device. Buttons with global functions always execute the same command, even if device is active. Buttons with functions per device execute commands depending on the active device. For example, the Left button is the Play command when the VCR is active.

Note:

Per-device functions overrule global functions. For example, when you program the Volume buttons globally but you assign a specific function to them with the tuner, the specific command will be executed when the tuner is the active device.

Programming a button globally

1.Tap the Home menu button .

2.Complete steps 2 to 7 in

“Programming control panel buttons” on page 23. Instead of tapping a button on the touchscreen, press the button you want to program.

The label of the button you have pressed (e.g. chan+ or left) starts blinking on the remote controller icon.

Programming a button per device

1.Switch to the device for which you want to program the button.

2.Complete instructions 2 to 7 in

“Programming control panel buttons” on page 23. Instead of tapping a button on the touchscreen, press the button you want to program.

The label of the button you have pressed (e.g. chan+ or left) starts blinking on the remote controller icon.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents USR-5RF Precautions CareTable of contents Quick Start Insert batteriesTouch the screen to start Operate your componentsQuick reference Quick referenceQuick reference ModesIntelligent Remote Controller Direct-access buttonsIntroduction Left and Right buttons Touchscreen buttonsWhich Buttons Can Be Programmed? Charging the Remote Controller AA batteriesOptional recharging dock Activate the remote controller Getting StartedDefine the Brand of Your Device Defining brands by selecting Select Yes to define the brand of the device to operateTap Next Navigate through the list of brands Select your brand from the listSelect a code set from the list Defining brands by searching Tap SearchSelect a Device Via the Home menuVia the Device menu Using touchscreen buttons Sending commandsOperate a Device ScrollingIR commands Device pages Adjust the Settings Touch and hold the remote controller icon for a few secondsTap the button of the setting you want to adjust Use the Left and Right button to adjust the settingSecond setup panel Third setup panelGetting the Maximum out of it IntroductionWorking with Modes Tap the mode you want to use To hide the Mode menuTap Programming Buttons Programming control panel buttonsProgramming direct-access and Left/Right Buttons Programming device itemsMake sure the device tab is active Labeling Buttons and Menu Items Labeling a buttonEdit the label Labeling a menu item Complete instruction 4 to 6 Labeling a button onAdding and Moving Devices Adding devicesMoving menu items Delete and restore DeleteDeleting a button or button function Restore Tap the item you want to restoreRecording Macros and Setting Timers Recording macrosSetting timers Editing macrosEditing timers Organizing macros and timers into groupsEdit the timer Press the Left button to close the timer Tap Create Timer Group or Create Macro GroupUsing the remote controller with Radio Frequency Changing the remote controller’s RF IR Settings Switch to RF IR mode by using Mode buttonTap RF Try the devices which you just changed the RF IR settings Changing the Extender IDSwitch back to RF IR mode Select a device that is set with RF signalsChoosing Another Channel Press the + and action buttons to change the ChannelChadEdit With ChadEdit you canSystem requirements Troubleshooting General Problems Programming ProblemsRecharging Problems Can I program a button to execute more than one command? How do I program source switching?How do I reset the Remote controller? How do I revert to the original configuration?Overview of Symbols Specifications Onkyo U.S.A. Corporation
Top Page Image Contents