Onkyo USR-5RF instruction manual Troubleshooting, General Problems Programming Problems

Page 39

Troubleshooting

General Problems

Programming Problems

The display is blank

•Tap the screen to make sure the Remote controller is turned on.

•Adjust the contrast dial on the left side.

•Make sure the batteries are properly installed.

•Install new batteries or recharge the battery pack using the recharging dock.

The display is too light or too dark

•Adjust the contrast dial on the left side.

The Remote controller shuts itself off

•This is a feature of the Remote controller to save power. You can change the length the Remote controller stays on in the Settings (see page 19).

Devices do not respond to commands from the Remote controller

•Make sure the Remote controller is in Use mode (see page 11).

•Make sure the Remote controller’s sending eye is pointed towards the device you are operating.

•Check if the Low Battery icon is blinking. If so, replace the batteries or recharge the battery pack.

•Check if the button you are trying to use is programmed properly (see page 23).

The Remote controller beeps 4 times after inserting the batteries

•Use ChadEdit to update the Remote controller’s software (ChadEdit > Tools > Update)

Buttons are not sending the correct commands

•Check whether the button is programmed globally or per device (see page 24).

Macros do not work

•Make sure the Remote controller’s sending eye is pointed towards the device the entire time the macro is being executed.

•Insert delays to allow devices to start up properly (see page 21).

•Check if you do not have included inactive buttons in your macro.

•Check if you do not have reprogrammed buttons. Macros can not save commands, they just save buttons. If you reprogram a button, the macro executes the new command assigned to the button.

The TV goes blank or the input source changes

•The Device menu item might be programmed to switch the input source. Operate the device without affecting the input source (see page 17).

The Remote controller will not edit, label or delete commands

•If the label locked appears on the Remote controller icon, the device control panels have been locked to prevent unwanted changes. You cannot modify or delete commands for this device.

•Make sure your devices are positioned as shown on page 23. Avoid programming the Remote controller under bright fluorescent light: it might affect the infrared signals.

•Make sure the button you want to edit has a border. Borderless buttons cannot be programmed.

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents USR-5RF Care PrecautionsTable of contents Operate your components Quick StartInsert batteries Touch the screen to startQuick reference Quick referenceModes Quick referenceIntelligent Remote Controller Direct-access buttonsIntroduction Left and Right buttons Touchscreen buttonsWhich Buttons Can Be Programmed? AA batteries Charging the Remote ControllerOptional recharging dock Activate the remote controller Getting StartedDefine the Brand of Your Device Defining brands by selecting Select Yes to define the brand of the device to operateTap Next Select your brand from the list Navigate through the list of brandsSelect a code set from the list Tap Search Defining brands by searchingSelect a Device Via the Home menuVia the Device menu Scrolling Using touchscreen buttonsSending commands Operate a DeviceIR commands Device pages Use the Left and Right button to adjust the setting Adjust the SettingsTouch and hold the remote controller icon for a few seconds Tap the button of the setting you want to adjustThird setup panel Second setup panelGetting the Maximum out of it IntroductionWorking with Modes Tap the mode you want to use To hide the Mode menuTap Programming control panel buttons Programming ButtonsProgramming direct-access and Left/Right Buttons Programming device itemsMake sure the device tab is active Labeling Buttons and Menu Items Labeling a buttonEdit the label Complete instruction 4 to 6 Labeling a button on Labeling a menu itemAdding and Moving Devices Adding devicesMoving menu items Delete and restore DeleteDeleting a button or button function Tap the item you want to restore RestoreRecording macros Recording Macros and Setting TimersEditing macros Setting timersTap Create Timer Group or Create Macro Group Editing timersOrganizing macros and timers into groups Edit the timer Press the Left button to close the timerUsing the remote controller with Radio Frequency Changing the remote controller’s RF IR Settings Switch to RF IR mode by using Mode buttonTap RF Changing the Extender ID Try the devices which you just changed the RF IR settings Press the + and action buttons to change the Channel Switch back to RF IR mode Select a device that is set with RF signals Choosing Another ChannelWith ChadEdit you can ChadEditSystem requirements General Problems Programming Problems TroubleshootingRecharging Problems How do I revert to the original configuration? Can I program a button to execute more than one command?How do I program source switching? How do I reset the Remote controller?Overview of Symbols Specifications Onkyo U.S.A. Corporation
Top Page Image Contents