Universal Remote Control omega MX-650 Edit the Main Menu Title or a Main Menu Device Label

Page 20

	T h e O m e g a
6	When you are finished editing the button, press the button you
	edited and “SAVED” will flash at the bottom of the display.
7	To change any other button labels on the same device, press the next
	button, then repeat steps 5-7. If you wish to edit a button on another
	device, press the MAIN button once, then repeat Steps 3-7.
8	Once you’ve finished editing buttons, press the MAIN button four
	times to return to normal operation.

Edit the MAIN Menu Title or a MAIN Menu Device Label

You can change the title of the MAIN Menu or a MAIN Menu device label by following these steps after you’ve entered TEXT Edit mode (described in the steps one through four in the preceding pages).

1	Once you’ve entered TEXT Edit mode, the top of the screen displays
	EDIT and the first ten devices of the MAIN Menu. There are five

pages you can access via the Page UP or DOWN buttons. When the top of the screen says EDIT, pressing a device button jumps to the pages for that device so that you can edit a device’s LCD buttons normally. However, if you continue to tap the Page button, the top of the screen will change from EDIT to MAIN. While it says MAIN, there are two pages of LCD but- tons. The first two list the Devices of the MAIN Menu and enable you to change the device names when pressed. The last page titled MAIN has only one entry for the LCD buttons; “MAIN”. When you press the corresponding hard button, you can relabel the MAIN title to the room the Omega controls.

2

3

4

Select the title to edit by pressing the adjacent hard button.

Edit the text (described on steps 4 and 5 on page 17).

Press the button you edited to save the changes. Here’s an example:

The MAIN Menu title has been changed to DEN, so whenever the MAIN button is pressed, the user is reminded that this is the DEN remote.

Each of the MAIN menu device buttons has been cus- tom labeled for the activities the user likes to use in the DEN. Unused devices are renamed with spaces and the pages of the unused devices are hidden so that an accidental press of a blank button does nothing.

18

Image 20

Contents Omega Thank You Table of Contents Battery Installation Getting StartedE O m e g a CongratulationsUniversal Remote Control, Inc Button LayoutLight Button TV Device ButtonBasic Setup Codes by sending power off commandsPre-Programmed Method Refer to the pre-programmed code tables on pages 37 52Other ten Device names Press the P-PRO button to select the Pre-Programmed MethodPress Button To display Gram a device named TV with codes from the Cable code tables Use the number buttons to enter the code numberSave Learning Method Top of the screen will change to LearnPress any Button Device button Press Button First ten To display Other tenDevice Names Display changes to either Good or Failed Volume Control Punch Through Press the Punch buttonChannel group Channel Up Left, Right, Sel Channel Down Prev CHYou select the device that has the volume commands you want Mode and test your Punch Through settingsBottom of the display will then flash Punch FROM. Now Surround sound receivers. The bottomSetting Backlight Options To setup your Favorite Channel buttons go toAdvanced Operation FAV ButtonUniversal Remote Control, Inc Adjusting Contrast Transmitting Busy Signal IconDisplay changes to the Edit menu. Press the Text button Advanced SetupEditing Button Labels Down Cursor Button deletes the currently Blinking character Want to EDIT, selecting between the FAV, MAIN, DEVICE, thenBlinking Character Edit flashes Edit the Main Menu Title or a Main Menu Device Label Edited and Saved will flash at the bottom of the displayDevice, press the Main button once, then repeat Steps Times to return to normal operationMacro Button Setup Press the Macro button. The top of the display will showMACRO. The bottom of the display will flash Select TonsMacro using the MAIN, Device and page buttons. Then press Favorite Channel Setup Returns to the Setup menu Appears at the top of the screen Hiding and Adding PagesPress the page button Want to ADD? or HIDE? the page displayed. When you would Want to editPages FAV Pages byErasing Erasing Learned Buttons, Macros or FavsE O m e g a Erasing the Entire Omega ALL Button erases all settingsCloning One Omega to Another Recalling Pre-Programmed Settings Using MRF-250 or MRF-300 Addressable Base Stations Utilizing Optional RF Base StationsUniversal Remote Control, Inc E O m e g a RF Settings Overview Changing the RF SettingsHere are the factory default RF settings of the Omega Only choice onExit this Menu IR/RF Signal SettingRF Button Displays Other Devices Devices of the Omega Or just one of the devices of the Omega Emitt Setting IR Emitter OutputsFrom the RF Settings Menu, select Emitt Blast Setting the Front Panel Blaster On or Off From the RF Settings Menu, select Blast Select ALL to change the blaster settings toPre-Programmed Code Tables Cable DVD VCR Audio SAT DVR Light AUX Webtv TapeTV TVs, Plasmas, Projectors and Monitors Brand Code NumbersKEC Cable Cable TV Descramblers/Tuners Comsat DVD-DVD Players DVD-DVD/VCR Combos DVD-TV/DVD CombosDVD-TV/DVD/VCR Combos VCR VCRs DVD-DVD RecordersDVD Laser Disc Players Instantreplay VCR TV/VCR Combos Audio Amps, Preamps and A/V ReceiversArcam Klipsch SAT Satellite Receivers CD CD Players and Changers Amend DVR Digital Video Recorders TiVo, Replay Light Lighting SystemsAUX Custom Installation Products Webtv Internet Browsers for TV Tape Tape, Cassette and Reel to Reel recordersFrequently Asked Questions WarrantySpecifications If the batteries run out, will I lose my settings?M O M O Complete Control TM