Universal Remote Control omega MX-650 owner manual Utilizing Optional RF Base Stations

Page 30

T h e O m e g a

Utilizing Optional RF Base Stations

You can use the Omega as you would your other remote controls. It trans- mits very powerful line-of-sight output using infrared light commands (invisible to the naked eye). When you point the Omega at the compo- nents, expect the range to be between 30 and 50 feet. When the remote is not pointed in the general direction of the components, the range will vary (depending on reflective surfaces, lighting, etc.).

However, the Omega also sends radio signals in every direction. By pur- chasing the MRF-100 or the addressable MRF-250 or MRF-300 base sta- tions, you can operate your equipment with the Omega 50 to 100 feet away (through walls, doors, cabinets, inside or outside). Since the RF Base Station picks up the Omega's radio signals from any direction, regardless of distance, the Omega doesn’t have to be pointed!

Using MRF-250 or MRF-300 Addressable Base Stations

By installing an MRF-250 or MRF-300 base station you gain freedom from interference from a nearby room, house or condo where someone else might be using an RF remote control. Addressable base stations are assigned one of 15 unique ID#’s. This allows multiple equipment loca- tions in one house to be controlled by any Omega. In operation it’s simple: when you select a device located in the Den, the Omega only talks to the base station in the Den. When you select a device located in the Family Room, the Omega only talks to it!

When used with an MRF-250 or MRF-300 base station, the Omega can be programmed to control identical components, for example, a media room array of TV’s . The intelligent routing of the MRF-250 or the MRF-300 base station will send your commands only to the TV you want to control. The other identical TV’s will not receive commands. Of course, if your system utilizes identical satellite receivers, cable boxes, VCR’s or disc changers you can utilize IR routing just as easily for them. If you have more than six identical components, up to 15 addressable MRF-250’s or MRF-300’s can be installed to control them (thus allowing up to 90 identical components in one house).

Note: The Omega's radio signals will not control components directly. Components that came with "no pointing" radio remote controls cannot

be operated by the Omega unless the component can be switched to standard infrared control via its internal menus. Some remote control ceiling fans are radio only and cannot be operated by the Omega.

28

Image 30
Contents Omega Thank You Table of Contents E O m e g a Battery InstallationGetting Started CongratulationsUniversal Remote Control, Inc Button LayoutLight Button TV Device ButtonPre-Programmed Method Basic SetupCodes by sending power off commands Refer to the pre-programmed code tables on pages 37 52Press the P-PRO button to select the Pre-Programmed Method Press Button To displayOther ten Device names Gram a device named TV with codes from the Cable code tables Use the number buttons to enter the code numberSave Learning Method Top of the screen will change to LearnDevice button Press Button First ten To display Other ten Device NamesPress any Button Display changes to either Good or Failed Channel group Volume Control Punch ThroughPress the Punch button Channel Up Left, Right, Sel Channel Down Prev CHBottom of the display will then flash Punch FROM. Now You select the device that has the volume commands you wantMode and test your Punch Through settings Surround sound receivers. The bottomAdvanced Operation Setting Backlight OptionsTo setup your Favorite Channel buttons go to FAV ButtonUniversal Remote Control, Inc Adjusting Contrast Transmitting Busy Signal IconAdvanced Setup Editing Button LabelsDisplay changes to the Edit menu. Press the Text button Want to EDIT, selecting between the FAV, MAIN, DEVICE, then Blinking Character Edit flashesDown Cursor Button deletes the currently Blinking character Device, press the Main button once, then repeat Steps Edit the Main Menu Title or a Main Menu Device LabelEdited and Saved will flash at the bottom of the display Times to return to normal operationMACRO. The bottom of the display will flash Select Macro Button SetupPress the Macro button. The top of the display will show TonsMacro using the MAIN, Device and page buttons. Then press Favorite Channel Setup Returns to the Setup menu Hiding and Adding Pages Press the page buttonAppears at the top of the screen Pages Want to ADD? or HIDE? the page displayed. When you wouldWant to edit FAV Pages byErasing Erasing Learned Buttons, Macros or FavsALL Button erases all settings Cloning One Omega to AnotherE O m e g a Erasing the Entire Omega Recalling Pre-Programmed Settings Using MRF-250 or MRF-300 Addressable Base Stations Utilizing Optional RF Base StationsUniversal Remote Control, Inc Here are the factory default RF settings of the Omega E O m e g a RF Settings OverviewChanging the RF Settings Only choice onIR/RF Signal Setting RF ButtonExit this Menu Displays Other Devices Devices of the Omega Emitt Setting IR Emitter Outputs From the RF Settings Menu, select EmittOr just one of the devices of the Omega Blast Setting the Front Panel Blaster On or Off From the RF Settings Menu, select Blast Select ALL to change the blaster settings toPre-Programmed Code Tables Cable DVD VCR Audio SAT DVR Light AUX Webtv TapeTV TVs, Plasmas, Projectors and Monitors Brand Code NumbersKEC Cable Cable TV Descramblers/Tuners Comsat DVD-DVD Players DVD-TV/DVD Combos DVD-TV/DVD/VCR CombosDVD-DVD/VCR Combos DVD-DVD Recorders DVD Laser Disc PlayersVCR VCRs Instantreplay VCR TV/VCR Combos Audio Amps, Preamps and A/V ReceiversArcam Klipsch SAT Satellite Receivers CD CD Players and Changers Amend DVR Digital Video Recorders TiVo, Replay Light Lighting SystemsAUX Custom Installation Products Webtv Internet Browsers for TV Tape Tape, Cassette and Reel to Reel recordersSpecifications Frequently Asked QuestionsWarranty If the batteries run out, will I lose my settings?M O M O Complete Control TM