Samsung 4 CHANNEL DVR, SDE-3003, SDE-3001 user manual Connecting WEB Viewer, Click Install

Page 68

web viewer

CONNECTING WEB VIEWER

1.Open your web browser and type the IP address or URL of DVR into the URL address box.

MThe basic URL of the DVR is as following in case of MAC address :

http://www.samsungipolis.com/User ID

You can also use registered URL which setups up in the Setup menu of your DVR.

2.Set the Admin ID and password same to those of the DVR Admin.

For general users, enter the DVR user ID and password.

J The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product.

Note that the security and other related issues caused by the unchanged password shall be responsible for the user.

M It allows up to 4 simultaneous access including the Admin and general users.

It does not allow multiple login of the Admin user.

Initial password of the Admin user is set to “4321”.

Password of the Admin and general users can be changed in <Permission Management> menu of the DVR.

Normal users should have set <Viewer> under <Permission Management> to “Use” before connecting to the Web Viewer. (Page 37)

All settings are applied by the DVR’s settings.

3.Click <Install ActiveX Control…>.

Downloading Active-X control may take several minutes according to the security settings on your PC.

4.Click <Install>.

68_ web viewer

Image 68

Contents Channel DVR Channel DVR Important Safety Instructions  OverviewOverview Battery Before StartContents Using Live Viewer Using Search ViewerViewer Setup SEC Backup ViewerFeatures Package Contents Standards ApprovalsPart Names and Functions Front Part Names and Functions Rear Changing the Remote Control ID Remote ControlUsing the Numeric buttons Installation Checking the Installation Environment Connecting with Other Device Only one mouse port is available Connecting the VIDEO, AUDIO, and MonitorConnecting the USB Connecting the Camera  Connecting with Other DeviceRJ-45 Cable Length 18.3m, 60ft IR LEDCamera Bracket Installing the cameraCamera Bracket Specification Adjusting the Camera Bracket Connecting the alarm output signal Connecting the Alarm INPUT/OUTPUTConnecting the alarm input signal Connecting to the Network using the router Connecting the NetworkConnecting to Network through Ethernet 10/100BaseT Connecting to Internet through Adsl InternetGetting Started Starting the systemShutting Down the System  LiveLogin Locking All ButtonsLive Live Screen ConfigurationIcons on the Live Screen Error Information Split Mode MenuSplit Mode Menu Live Screen MenuSingle Mode Menu System Date/Time/Language Time. Alarm FreezeView the Launcher Menu Live Mode Switching the screen modeSwitching the screen automatically PIPChannel Setting Switching to Single ModeSelecting a Spot Out mode Spot OUTZoom Multichannel Live MenuAudio ON/OFF in Single mode Audio ON/OFFFreeze Event MonitoringCH2 Date/Time/Language System SetupSetting the Date/Time/Language Setting Holiday Using the CalendarSetting the Administrator Using Virtual KeyboardPermission Management Permission ManagementSetting the Group To set the group authorityTo change the user password To restrict the user permissionsSetting the User Setting PermissionsWhen the user setup is done, press OK  Using the DVRSystem Management System ManagementChecking the System Information  Using Updating the SoftwareSystem Log SettingsLog Information Backup Log Event LogUse the up/down buttons Select Event Log Use direction buttonsSetting the Device Setting the CameraCamera Press Enter buttonWhen the camera setup is done, press OK Storage DeviceConfirming Devices You can check information on storage devicesFormatting You can format a storage deviceSelect Format FormattedRemote Device HDD AlarmRemote Devices Setting the Monitor Setting Display positionMonitor Move to Monitor, and press Enter buttonSetting the Spot Out Setting the Screen ModeSetting the Recording Recording ScheduleRecord Recording ScheduleREC Quality / Resolution Setting Standard Recording PropertiesEvent Record Duration Recording Color TagsSetting Event Recording Properties Record OptionSetting the Event Window of sensor detection setup appearsSensor Detection Detection, and press Enter buttonSetting the Motion Detection Area Motion DetectionAlarm Schedule Window of video loss detection area setup appearsWhen the Alarm Schedule setup is done, press OK Video Loss DetectionBackup Setting the BackupYou can backup the desired data to a connected device BackupNetwork Configuration Connection ModeSetting the Connection You can set the network connection route and protocolSetting the Protocol Move to Connection Mode, and press EnterConnecting and Setting the Network When no router is usedWhen a router is used Internal Port Range Set the same to the External Port RangeLive Transfer Ddns SettingLive Transfer Event Setting Mailing ServiceSmtp Setting When the recipient setting is done, press OK Group SettingRecipient Setting It does not appear in Backup Search SearchTime Search You can search for recorded data of a desired timeSearch & Play Backup SearchEvent Search Motion Search Motion SearchBackup Range PlaybackPlay  For data search, refer to Search.Using the Playback Button REC Records all channels in Live mode Partial BackupMode Switch DVR set WEB Viewer What is Web Viewer?Introducing WEB Viewer Connecting WEB Viewer Click InstallUsing Live Viewer You can change the split mode by clicking each number icon Single ModeQuad Mode Full Screen ModeSetting the display of the OSD time information Connected DVRSaving the Live Screen on the PC Capture Saves the current screen into a BMP or Jpeg fileUsing Search Viewer SPLIT-SCREEN Saving the Live Screen on the PC Searching the Recorded Video in the Calendar Viewer Setup You can configure the various settings of the DVR systemSystem Date/Time/LanguageHoliday Permission ManagementSystem Management Storage Device DeviceCamera Remote Device MonitorFor more information, refer to Setting the Recording. RecordRecording Schedule Event Record DurationREC Quality & Resolution EventRecord Option Sensor DetectionAlarm Schedule You can set the alarm output time if a video loss occursMotion Detection Video Loss DetectionFor more information, refer to Network Configuration. You can check the Ddns settingsNetwork ConnectionMailing Service SmtpWhat is Mobile Viewer? Key FeaturesAbout Mobile ViewerSEC Backup Viewer Recommended System Requirements Backup Viewer Product Specification Camera UTP Appendix Weight 300g 115gHumidity Mechanical Product Specification 500GB Sata HDD 1TB Sata HDDHdmi Management Default SettingCategory Details Factory Default Duration 4CIFLSmtp Troubleshooting 4CIF 2CIFCIF Open Source License Report on the Product PreambleVersion 2, June USAPage No Warranty GNU Lesser General Public License instead of this License How to Apply These Terms to Your New ProgramsSome devices are designed to deny users access to Terms and Conditions Source CodeConveying Verbatim Copies Additional Terms Acceptance Not Required for Having Copies Automatic Licensing of Downstream RecipientsRevised Versions of this License PatentsUse with the GNU Affero General Public License END of Terms and Conditions Limitation of LiabilityInterpretation of Sections 15 Page Modified work must itself be a software library Page How to Apply These Terms to Your New Libraries OpenSSL License Original SSLeay LicensePage Correct disposal of batteries in this product Sales Network Chertsey, Surrey, United Kingdom KT16 OPS