Samsung SDE-3003, SDE-3001 Setting the Device, Setting the Camera, Press Enter button

Page 42

using the DVR

SETTING THE DEVICE

You can setup Camera, Storage Device, Remote Device and Monitor.

Camera

Setting the Camera

You can set Video, Audio, Channel Name and Dwell Time of a Camera.

Using the mouse may help make setup easier.

1.Press the [MENU] button on the remote control.

2.Use the left/right button (◄ ►) to select <Device>. Device setting menu is selected.

3. Use the up/down buttons (

) to move to <Camera>,

and press [ENTER] button.

 

Logout

Device

Camera

Storage Device

Remote Device

Monitor

Return

4.Select <Camera>.

You will see a window where you can configure the camera settings including Video, Audio, CH Name, SEQ- Dwell Time.

5. Use direction buttons (

) to move to a desired

item, and set the value.

 

Video

-<ON/OFF> : You can turn ON/OFF the selected channel’s camera.

Camera

Camera

CH

Video

 

Audio

 

CH Name

SEQ-Dwell Time

 

1

ON

OFF

CAM 01

5 sec

2

ON

OFF

CAM 02

5 sec

3

ON

OFF

CAM 03

5 sec

4

ON

OFF

CAM 04

5 sec

Screen Setup

OK Cancel

-<Covert1> : Shows information other than the video of the selected channel.

For privacy protection, it does not display the video while the recording continues.

-<Covert2> : Shows nothing but an empty screen while the recording continues.

Audio

-If set to <ON>, you can turn the audio of the channel ON/OFF on the Live screen.

-If set to <OFF>, the channel’s audio is off on the Live screen and not recorded.

-For SEB-1006R (MIC integrated camera), you must connect it to CH1 and set CH1 Audio to “ON” in the Camera menu.

Audio output is available for only CH1.

42_ using the DVR

Image 42
Contents Channel DVR Channel DVR Important Safety Instructions  OverviewOverview Battery Before StartContents Viewer Setup Using Live ViewerUsing Search Viewer SEC Backup ViewerFeatures Package Contents Standards ApprovalsPart Names and Functions Front Part Names and Functions Rear Remote Control Using the Numeric buttonsChanging the Remote Control ID  Connecting with InstallationChecking the Installation Environment Other DeviceConnecting the VIDEO, AUDIO, and Monitor Connecting the USB Only one mouse port is available RJ-45 Cable Length 18.3m, 60ft Connecting the Camera Connecting with Other Device IR LEDInstalling the camera Camera Bracket SpecificationCamera Bracket Adjusting the Camera Bracket Connecting the Alarm INPUT/OUTPUT Connecting the alarm input signalConnecting the alarm output signal Connecting the Network Connecting to Network through Ethernet 10/100BaseTConnecting to the Network using the router Connecting to Internet through Adsl InternetShutting Down the System Getting StartedStarting the system  LiveLogin Locking All ButtonsLive Screen Configuration Icons on the Live ScreenLive Split Mode Menu Error InformationSplit Mode Menu Live Screen MenuSingle Mode Menu Alarm Freeze View the Launcher MenuSystem Date/Time/Language Time. Switching the screen automatically Live ModeSwitching the screen mode PIPChannel Setting Switching to Single ModeZoom Selecting a Spot Out modeSpot OUT Multichannel Live MenuFreeze Audio ON/OFF in Single modeAudio ON/OFF Event MonitoringCH2 System Setup Setting the Date/Time/LanguageDate/Time/Language Setting Holiday Using the CalendarPermission Management Setting the AdministratorUsing Virtual Keyboard Permission ManagementSetting the Group To set the group authorityTo change the user password To restrict the user permissionsWhen the user setup is done, press OK Setting the UserSetting Permissions  Using the DVRSystem Management Checking the System InformationSystem Management  Using Updating the SoftwareSettings Log InformationSystem Log Use the up/down buttons Backup LogEvent Log Select Event Log Use direction buttonsCamera Setting the DeviceSetting the Camera Press Enter buttonConfirming Devices When the camera setup is done, press OKStorage Device You can check information on storage devicesSelect Format FormattingYou can format a storage device FormattedHDD Alarm Remote DevicesRemote Device Monitor Setting the MonitorSetting Display position Move to Monitor, and press Enter buttonSetting the Spot Out Setting the Screen ModeRecord Setting the RecordingRecording Schedule Recording ScheduleEvent Record Duration REC Quality / ResolutionSetting Standard Recording Properties Recording Color TagsSetting Event Recording Properties Record OptionSensor Detection Setting the EventWindow of sensor detection setup appears Detection, and press Enter buttonSetting the Motion Detection Area Motion DetectionWhen the Alarm Schedule setup is done, press OK Alarm ScheduleWindow of video loss detection area setup appears Video Loss DetectionYou can backup the desired data to a connected device BackupSetting the Backup BackupSetting the Connection Network ConfigurationConnection Mode You can set the network connection route and protocolSetting the Protocol Move to Connection Mode, and press EnterConnecting and Setting the Network When no router is usedWhen a router is used Internal Port Range Set the same to the External Port RangeDdns Setting Live TransferLive Transfer Mailing Service Smtp SettingEvent Setting Group Setting Recipient SettingWhen the recipient setting is done, press OK Time Search It does not appear in Backup SearchSearch You can search for recorded data of a desired timeBackup Search Event SearchSearch & Play Motion Search Motion SearchPlay Backup RangePlayback  For data search, refer to Search.Mode Switch Using the Playback ButtonREC Records all channels in Live mode Partial Backup DVR setWhat is Web Viewer? Introducing WEB Viewer WEB Viewer Connecting WEB Viewer Click InstallUsing Live Viewer Quad Mode You can change the split mode by clicking each number iconSingle Mode Full Screen ModeSetting the display of the OSD time information Connected DVRSaving the Live Screen on the PC Capture Saves the current screen into a BMP or Jpeg fileUsing Search Viewer SPLIT-SCREEN Saving the Live Screen on the PC Searching the Recorded Video in the Calendar System Viewer SetupYou can configure the various settings of the DVR system Date/Time/LanguageHoliday Permission ManagementSystem Management Device CameraStorage Device Remote Device MonitorRecording Schedule For more information, refer to Setting the Recording.Record Event Record DurationRecord Option REC Quality & ResolutionEvent Sensor DetectionMotion Detection Alarm ScheduleYou can set the alarm output time if a video loss occurs Video Loss DetectionNetwork For more information, refer to Network Configuration.You can check the Ddns settings ConnectionMailing Service SmtpAbout What is Mobile Viewer?Key Features Mobile ViewerSEC Backup Viewer Recommended System Requirements Backup Viewer Product Specification Camera UTPWeight 300g 115g Humidity Mechanical Appendix Product Specification 500GB Sata HDD 1TB Sata HDDHdmi Default Setting Category Details Factory DefaultManagement Duration 4CIFLSmtp Troubleshooting 4CIF 2CIFCIF Version 2, June Open Source License Report on the ProductPreamble USAPage No Warranty How to Apply These Terms to Your New Programs Some devices are designed to deny users access toGNU Lesser General Public License instead of this License Terms and Conditions Source CodeConveying Verbatim Copies Additional Terms Acceptance Not Required for Having Copies Automatic Licensing of Downstream RecipientsPatents Use with the GNU Affero General Public LicenseRevised Versions of this License Limitation of Liability Interpretation of Sections 15END of Terms and Conditions Page Modified work must itself be a software library Page How to Apply These Terms to Your New Libraries OpenSSL License Original SSLeay LicensePage Correct disposal of batteries in this product Sales Network Chertsey, Surrey, United Kingdom KT16 OPS