Sunwave Tech manual SRC-7000 User’s Manual

Page 38

SRC-7000 User’s Manual

Tap soft button to start auto searching. When you see the targeted device has been turned off, tap or press any button

immediately to stop auto searching. Then press to test the power key. If it can’t work, please go through step as below.

Tap or gently to figure out the correct remote code (Code number as shown on the top middle position of the LCD.) until the targeted device has been turned on again. Press the power key or the hard key to test and to confirm the codes.

If the codes are not correct please repeat steps and select “All”. Repeat the ~again to find the proper code for your target device.

If you still can’t find the proper code for your device, please select “All” in the Brand item then tries to auto search the code again.

After the Pre-code auto search is finished the LCD will show a “Search completely” message and an “OK” icon. Tap the “OK” to exit the auto search. This means the SRC-7000 has already search the defined area codes already. The codes might not include in the pre- code database.

5.In this page, you will find an icon which is the “Key Pad Entry” function. You can also press the icon to enter the “Key Pad Entry” function.

6.Key in the code number for your device directly. In this way, you are able to save the time to load the corresponding codes. However, each brand may have several remote codes. You may need to load the remote codes several times to find the correct codes for your device.

7.If they work, it means that you have found the correct remote codes.

Please press the button to confirm your decision.

8.If you intend to setup another device code, please repeat step 3~7.

If you still can’t use Pre-code to load correct code for your device, please use “Learning Function” on next section.

36

Image 38

Contents User’s Manual 041201Copyright PrefaceAbout this manual TrademarksTable of Contents Macro Timer Macro Pre-code LearningInstall the SLC-2080 USB Driver Introduction to the SRC-7000 SRC-7000 Features Unpacking the SRC-7000Battery Installation Remove battery coverBattery Precautions Turning the Touch Screen OnIdentifying Components Top of SRC-7000Botton of SRC-7000 Direct Access Buttons Rubber Keys Setup mode function Device normal functionPrecautions When Using the Touch Screen LCD Touch ScreenTouch Screen Keys Touch screen buttonsMain Menu Basic Information Layout Key Layout Setup Mode Code Setting Setup ModeTimer Macro Setup Mode Quick Start Re-calibrating the ScreenDate / Time Setting Device Setting SRC-7000 User’s Manual Create a New Device How to Set Up Your SRC-7000Add a Device Next row How to Set Up Your SRC-7000 Load the Codes for the Newly-added DeviceSRC-7000 User’s Manual Learning SRC-7000 User’s Manual Add a Soft Key SRC-7000 User’s Manual Adding Text Re-label a Device, Key or Text How to Set Up Your SRC-7000 Re-size a Device, Key or Text Delete a Device, Key or Text SRC-7000 User’s Manual Pre-programmed Code SRC-7000 User’s Manual Learning SRC-7000 User’s Manual Learning successfully Learning fail Learn a Cycle Key Delete Device / Key Codes Create a Macro MacroIf you intend to create another Macro key, please repeat ~5 An Example of setting a Macro Basic Device Required Macro Sequence OperationTimer Macro Create a Timer MacroSRC-7000 User’s Manual Delete Your Timer Macro Re-label Your Timer Macro View Your Timer Macro Set Up Your Favorite Channels Add Favorite Channel KeysSet Your Favorite Channels as Macros NopSet Up the Remote MenusContrast PowerTime DateLight Period LCD OffLight Sensitivity Reset MotionKey Layout Code Setting Timer Macro ViewDuplicate DuplicateSRC-7000 User’s Manual Introduce SLC-2080 USB Cable Install USB Cable and SoftwareInstall the SLC-2080 USB Driver SRC-7000 User’s Manual Install Upgrade Tools SRC-7000 User’s Manual Install USB Cable and Software Upgrade Vmcu Firmware and Vmcf Pre- programmed Codes From File Backup RemoteFrom Internet SRC-7000 User’s Manual Features Appendix aSpecifications CD, AUXSLC-2080 USB Cable Transmit Cable Optional AccessoriesAppendix B SDS-7000 SDS-7000 Docking StationTroubleshooting Tables Appendix CTrying to configure