Sunwave Tech SRC-7000 manual Trying to configure

Page 75

Problem

 

Solution

 

 

 

You see an “error” display

The key that you pressed has not been taught or input the IR

during operation.

 

code.

 

Teach the key via learning procedure. (P.37)

 

 

 

IR Learning is not

Do not use the learn function near an incandescent lamp.

successful.

Memory capacity is full (64 keys for each device.).

 

Replace new batteries in the SRC-7000 and the remote you are

 

 

trying to configure.

 

Keep the learning distance between the remote control and

 

 

SRC-7000’s learning eye about 2~4 inches apart (5-10cm).

 

The learning process has no errors, but you still can’t control

 

 

your target devices:

 

 

- The battery in the target remote doesn’t have enough

 

 

power.

 

 

- Original remote might not be compatible with learning

 

 

procedure. Repeat the learning procedure again.

 

 

- If you still can’t solve the problem, contact SUNWAVE for

 

 

help.

 

 

 

Macro does not work.

Be sure to aim the SRC-7000 at the devices while the Macro

 

 

 

commands are being sent.

 

Macro was not properly set up. Repeat macro set-up

 

 

procedure. (P.42)

 

 

 

A key of your existing

Some remotes issue multiple commands when a key is held

remote performs two or

 

down. Please be sure to teach different keys of SRC-7000 for

more functions

 

 

these different commands.

 

 

 

Each key of SRC-7000 can learn 6 commands in a Cycle key.

 

 

(P.40)

 

 

 

The LCD screen turns off.

The SRC-7000 is preset automatically to switch the LCD off

 

 

 

after 1 minute by default if left unused. You can also setup the

 

 

idle time to turns off the LCD. (P.54)

 

You can turn on the SRC-7000 again as followed:

 

 

- Tap the touch screen

 

 

- Pick up the SRC-7000

 

 

- Press the hard key

 

 

 

The touch panel isn’t

Please re-calibrate your touch panel (P.17)

sensitivity

 

 

 

73

Image 75
Contents 041201 User’s ManualTrademarks PrefaceAbout this manual CopyrightTable of Contents Pre-code Learning Macro Timer MacroInstall the SLC-2080 USB Driver Introduction to the SRC-7000 Unpacking the SRC-7000 SRC-7000 FeaturesRemove battery cover Battery InstallationTurning the Touch Screen On Battery PrecautionsTop of SRC-7000 Identifying ComponentsBotton of SRC-7000 Setup mode function Device normal function Direct Access Buttons Rubber KeysLCD Touch Screen Precautions When Using the Touch ScreenTouch screen buttons Touch Screen KeysMain Menu Basic Information Layout Code Setting Setup Mode Key Layout Setup ModeTimer Macro Setup Mode Re-calibrating the Screen Quick StartDate / Time Setting Device Setting SRC-7000 User’s Manual How to Set Up Your SRC-7000 Add a DeviceCreate a New Device Next row Load the Codes for the Newly-added Device How to Set Up Your SRC-7000SRC-7000 User’s Manual Learning SRC-7000 User’s Manual Add a Soft Key SRC-7000 User’s Manual Adding Text Re-label a Device, Key or Text How to Set Up Your SRC-7000 Re-size a Device, Key or Text Delete a Device, Key or Text SRC-7000 User’s Manual Pre-programmed Code SRC-7000 User’s Manual Learning SRC-7000 User’s Manual Learning successfully Learning fail Learn a Cycle Key Delete Device / Key Codes Macro Create a MacroIf you intend to create another Macro key, please repeat ~5 Basic Device Required Macro Sequence Operation An Example of setting a MacroCreate a Timer Macro Timer MacroSRC-7000 User’s Manual Delete Your Timer Macro Re-label Your Timer Macro View Your Timer Macro Add Favorite Channel Keys Set Up Your Favorite ChannelsNop Set Your Favorite Channels as MacrosMenus Set Up the RemoteDate PowerTime ContrastLCD Off Light SensitivityLight Period Motion ResetKey Layout Code Setting View Timer MacroDuplicate DuplicateSRC-7000 User’s Manual Install USB Cable and Software Install the SLC-2080 USB DriverIntroduce SLC-2080 USB Cable SRC-7000 User’s Manual Install Upgrade Tools SRC-7000 User’s Manual Install USB Cable and Software Upgrade Vmcu Firmware and Vmcf Pre- programmed Codes Backup Remote From InternetFrom File SRC-7000 User’s Manual Appendix a FeaturesCD, AUX SpecificationsSDS-7000 SDS-7000 Docking Station Optional AccessoriesAppendix B SLC-2080 USB Cable Transmit CableAppendix C Troubleshooting TablesTrying to configure