Mitsubishi Electronics WD-52825, WD-62825 manual 104

Page 104

Troubleshooting, continued

 

Problem

 

Possible Solution

 

 

42.

The IEEE 1394 device cannot be selected.

• The device may be busy, either recording or a peer-to-peer

 

 

 

connection has been established. Cancel the recording or

 

 

 

peer-to-peer connection.

 

 

 

43.

DEVICE MENU button does not display a menu.

• The IEEE 1394 device does not provide a menu.

 

 

• The TV cannot support IEEE 1394 menus. See page 46.

 

 

 

44.

All IEEE 1394 devices disappear.

• The connected devices must not be in a loop that returns to the

 

 

 

TV. Make sure a device is connected at the end.

 

 

• Disconnect all the cables and devices from the TV. Replace them one

 

 

 

by one to locate the problem device or cable.

 

 

• Use System Reset (front control panel).

 

 

 

45.

Cannot rediscover a deleted IEEE 1394 device

• The device has been disconnected. Plug it in.

 

 

• The device is unchecked in the Review screen. Select NetCommand

 

 

 

from the Main menu, then select Review. Check the device.

 

 

• Remove IEEE 1394 plug. Go to the Edit NetCommand menu. Delete

 

 

 

the IEEE 1394 device. Plug the device in again so it can be

 

 

 

discovered again.

 

 

 

46.

An IEEE 1394 device has been plugged in but

• The IEEE 1394 connection to the TV or another device is not secure

 

does not appear in the Device Selection menu

 

or is loose.

 

(not discovered).

• The IEEE 1394 device is not powered on.

 

 

• A device in the IEEE 1394 chain is not powered on - turn on all the

 

 

 

devices.

 

 

• The device discovery can take as long as a minute to initiate.

 

 

• IEEE 1394 cable is too long (maximum of 15 feet between devices).

 

 

• The IEEE 1394 device uses an incompatible protocol and will not be

 

 

 

discovered

 

 

 

47.

Cannot record to or from the IEEE 1394 device,

• To initiate a recording to IEEE 1394 device press the REC key.

 

including Dub recordings.

 

The Record menu displays allowing setup of the recording.

 

 

• The source device for the recording is not powered on.

 

 

• When dubbing, the destination device for the recording

 

 

 

is not powered on.

 

 

• The wrong media, (analog tape for digital recording, or

 

 

 

digital tape for the analog recording) is in the device.

 

 

• Either the program is copy protected, or if there are multiple

 

 

 

subchannels and one of the programs (not necessarily the

 

 

 

program requested) is copy protected.

 

 

• The program has already been recorded once and the copy

 

 

 

protection only allows one recording.

 

 

• Unapproved source device for copy protected material.

 

 

• The recording device can not decode the copyright signal

 

 

 

included in the signal source (try another device if available).

 

 

• The playing device (for dubbing) does not support

 

 

 

copyrighted material.

 

 

• Source for recording is copyrighted.

 

 

• Too many IEEE 1394 devices in network. Insufficient

 

 

 

bandwith available. Disconnect unused devices.

 

 

• Source Device has higher speed (S 400) than record device. If

 

 

 

possible, reverse devices, play in the slower device and record

 

 

 

in the faster device.

 

 

 

48.

Cannot control the IEEE 1394 device from the

• Device may not support the command.

 

Transport Menu.

• Selected function is gray (such as Record for a DVD, which does not

 

 

 

support the Record function).

 

 

 

 

49.

When ChannelView™ list is displayed,

•

Available information is sent from the broadcaster or cable provider.

 

information appears incomplete

 

No other data is available.

 

 

 

 

50.

Program to be recorded was correctly selected

•

The broadcaster supplied program information that was incorrect

 

from ChannelView, however, incorrect program

 

and/or was changed after a recording was added to the Record List.

 

was recorded.

 

 

 

 

 

 

51.

Incomplete ChannelView program recorded.

•

Recording device may have lack of space availability and there is not

 

 

 

enough blank space to make a full recording.

 

 

 

 

104

Page 103 Page 105
Image 104
Page 103 Page 105
Contents Owner’s Guide Stand Requirement FCC Declaration of Conformity Contents TV Menu Screen Operations Ieee 1394 Devices and NetCommand Controlled RecordingsSpecial Features Important Safeguards Important Safeguards Our Thanks Mitsubishi Digital Electronics America, IncBack Panel TV Accessories Special Features Front Control PanelTelevision Overview TV Accessories Special Features System Reset IndicatorsReset Front Control PanelInput Front Panel Inputs and Media Card SlotsMedia Card Slots and Ieee 1394 Input/Output Back Panel CableCARD SlotInput-DTV Component-1, -2 InputsIR Emitter-NetCommand PC Input and AudioDTV Link/IEEE1394 DVI Analog AudioPage Connecting Connecting External Devices & NetCommand Setup ChartCable Box Connecting a Wall Outlet Cable or Cable BoxWall Outlet Cable Using a CableCARD CableCARD TechnologyConnecting a Lead Antenna or Separate UHF and VHF Antenna Separate UHF and VHF AntennaFor antennas with twin flat lead For cable or antenna with coaxial leadConnecting a VCR to an Antenna or Wall Outlet Cable Connecting a Cable Box to a VCR Audio & Video Cable Box Back panelConnecting an A/V receiver Connecting a DVD Player with Component DTV Connectors and Adaptors DTV Receiver with Component VideoDTV Receiver to TV Back Panel Connecting a DTV Receiver with RGB, HV VideoDTV Receiver with RGB, HV Video Link Control RS-232C Connection LinkConnecting the IR Emitter NetCommand Quadruple IR Emitter cable is included with the TVConnecting Compatible Ieee 1394 Devices When Connecting Ieee 1394 DevicesDigital Video Signals Digital Audio SignalsPin Style vs -Pin Style Connectors Connection StylesDirect Device-To-Device Style Hub Connection StyleConnecting Helpful Hints NetCommand Setup and Editing Using the Remote Control with NetCommand NetCommand Pre-Memorized DevicesRemote Control Functions Overview OverviewRemote Control FunctionsOperation and Care, Sleep Timer For Best Results from the Remote ControlInstalling the Batteries Setting the Sleep TimerNetCommand Setup On Screen Buttons Remote Control Buttons 3D Graphical Menu SystemNetCommand Initial Setup NetCommand Information ScreenDevice Setup Screen Welcome ScreenReview Screen Review screenReceiver Inputs Edit NetCommand, Add an A/V ReceiverReceiver Screen Receiver Input Learn Screen Receiver Learn ScreenName Screen Monitor Out to AVR ScreenAdd Screen Edit NetCommand, Add DevicesEdit NetCommand Screen Device Learn Screen Edit NetCommand Add DevicesDevice Screen Device Advanced Learn Screen Connection for Device ScreenVCR for Recordings Screen RF Connection for Cable ScreenInput-DTV Connection Screen IR Code for Device ScreenDelete Device Screen Edit NetCommand, Change or Delete Devices, Finish ScreenChange Device Screen PC Viewing Ieee 1394 Devices NetCommand Controlled RecordingsDevice Selection Menu Ieee 1394 Devices and NetCommand Control Adding Ieee 1394 Devices Automatically Adding Ieee 1394 Devices AutomaticallyNew 1394 Device Screen Name for 1394 Device ScreenIeee 1394 Device Type Screen Connection ScreenPIP Device Selection Menu Power On/Off DevicesDevice Selection Menu Using the Device Menu Button to Display Menus Device MenuIR Controlled Devices CableCARD MenuUsing the Guide Button to Display ChannelView and Menus Guide and the Device Selection MenuGuide and the Record To Menu Guide and ChannelViewRecording Now Setting up RecordingsTime-Delayed Recording Setting up a Peer-to-Peer Connection Cancel Current RecordingsCanceling a Peer-to-Peer Connection Record List, Peer-to-Peer ConnectionsUsing TV Disc & A/V Discs TV Disc & A/V Disc Track List ScreenTV Disc or A/V Disc Search Archiving TV Disc Digital RecordingsRestrictions for Traditional VCRs Direct VCR Recording from an Antenna or Cable SourceCopy-Protected Material PC Viewing PC InputMediaCommand and Media Card Playback Media Card SlotsInserting a media card Don’t pull the media card out while it is playingMedia Command and Media Card Playback TV Menu Screen Operations Main menu, Setup selected Main Menu ChoicesSetup Menu LanguageColor Balance TV PauseControlling the TV Pause Features Software VersionNetCommand Menu Antenna Menu MemorizePrefer Digital ChannelAntenna Menu, SuperQuickView SQV SQV SuperQuickViewTime Menu Captions Menu Analog and Digital Captions Captions Menu, Customizing Digital Settings Chip Lock Menu Chip Lock Menu OverviewSelecting a Passcode from the V-Chip Lock Menu Front Button LockUsing the V-Chip from the Remote Control Using V-Chip with Program RatingsUsing the Passcode from the V-Chip Lock Menu Chip Signal Information Content CategoriesChip Rating Guidelines TV RatingsAudioVideo Menu Setting Descriptions Audio Analog and Digital Audio SettingAnalog Only Audio Settings Digital Only Audio SettingsFor a Currently Viewed PC Setting Descriptions VideoVideo Settings Operation of PIP and POP Page Index WarrantyAdditional Information DVD Definitions Signals and Formats DefinitionsDisplay Formats Original Signal TV Display FormatsPC Display Formats Device Control with Net Command NetCommand Compatible Traditional Devices AnalogWhen an Ieee 1394 Device is Viewed or Played Ieee 1394 DevicesBypassing Front Button Lock Appendix a Bypassing the V-Chip LockBypassing the V-Chip Lock This page intentionally blank Inputs Appendix B SpecificationsTV Specifications Outputs Appendix CRemote Control Programming Codes Programming the Remote to Control NetCommand A/V ProductsAppendix C Remote Control Programming Codes DVD PlayersCable Boxes and Satellite Receivers ReceiversMitsubishi A/V Receivers Mitsubishi CD Players Not all functions for all modelsAppendix D On Screen Information Displays Appendix E NetCommand Specialized Device Keys Screen Remote Checkbox NameAppendix F Cleaning and Service To Install the Diamond Shield Appendix G Diamond Shield RemovalTo Remove the Diamond Shield For further assistance, call 800Appendix H Filter Cleaning Appendix H Lamp Cartridge Replacement Lamp Life100 Replacing the Lamp Cartridge101 TroubleshootingProblem Possible Solution 102 103 104 Using The System Reset Button 105Additional Information 106Index 107108 Icon Order, Viewing, Changing 67 IEEE1394Mitsubishi TV Software 109Mitsubishi DLP Projection Television Limited Warranty 110This Warranty does not Cover 111MDEAservice@mdea.com Website
Top Page Image Contents