Mitsubishi Electronics WD-52825, WD-62825 manual Connecting an A/V receiver

Connecting an A/V Receiver or Stereo System or a Satellite Receiver or Other Device with S-Video

A/V Receiver or Stereo System

Figure 7

A digital audio cable and stereo audio cables are required. The digital audio cable is provided. The stereo audio cables are not included with the TV.

Satellite Receiver or Other Device with S-Video

Figure 8

An S-Video cable and audio cables are required. These are not included with the TV.

1.Connect a set of stereo audio cables from OUTPUT AUDIO 2 on the TV back panel to the TV AUDIO INPUT on the back of the A/V receiver. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel.

To connect a digital A/V receiver with Dolby® Digital surround sound:

2.Connect one end of the digital audio cable supplied with the TV to DIGITAL AUDIO on the back of the TV. Connect the other end to the COAXIAL DIGITAL INPUT on the back of the A/V receiver.

Check A/V receiver’s Owner’s Guide for information concerning the use of the digital input and switching between the digital sound and analog stereo sound from the TV.

TV back panel section			1. Red		White
		IEEE1394
		INPUT/OUTPUT
	IR EMITTER		PC
	NetCommand		VGA/SVGA/XGA/
			720p	AUDIO				MONITOR
			60 Hz	L(MONO)		VIDEO	S-VIDEO
			R					OUTPUT
	DVI		L
L	Analog Audio							AUDIO 2
R		ANT-2	R
		AUX	PC-					AUDIO/VIDEO 1
			AUDIO
		DTV/
		CABLE/						INPUT-1
		VHF/
		UHF
HDMI		ANT-1	PC-					INPUT-2
M-LINK		MAIN	INPUT
	M-LINK
	CONTROL/
	RS-232C		DIGITAL
			AUDIO
		2.	Use only if
			connecting
			a Dolby Digital
			A/V Receiver
			A/V Receiver Rear Panel
								2.
								INPUT-2
								(COAXIAL)
White
			L
Red		1.	R
			IN
			TV

Figure 7. Connecting an A/V receiver

1.Connect an S-Video cable from VIDEO OUT on the satellite receiver back panel to INPUT-2 VIDEO on the TV back panel.

2.Connect a set of audio cables from AUDIO OUT on the satellite receiver back panel to INPUT-2 AUDIO, on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel.

Note: Refer to the Satellite Receiver Owner’s Guide for Dish Antenna connections.

TV back panel section
		IEEE1394
	INPUT/OUTPUT
	IR EMITTER		PC
	NetCommand R	VGA/SVGA/XGA/
			720p	AUDIO			MONITOR
			60 Hz
				L(MONO) VIDEO		S-VIDEO
			R				OUTPUT
	DVI		L
L							AUDIO 2
	Analog Audio
R	ANT-2		R
	AUX		PC-				AUDIO/VIDEO 1
			AUDIO
	DTV/
	CABLE/						INPUT-1
	VHF/
	UHF
HDMI	ANT-1		PC-				INPUT-2
M-LINK	MAIN		INPUT
	M-LINK
	CONTROL/					1.
	RS-232C	DIGITAL
		AUDIO
			Red		White
			2.
		Any S-Video Device
			AUDIO OUT	AUDIO IN	VIDEO OUT		1.
	2.	White
			L	L	(Y/C)
		Red	1
			R	R

Figure 8. Connecting a Satellite Receiver with S-Video

Note: NetCommand® will asssume you connected your Satellite Receiver to Input-2. If you add a second Satellite Receiver or use any other inputs for your Satellite Receiver, this change must match in the NetCommand system. See Editing NetCommand Setup in Chapter 3 for more information.

24