Eiki EIP-3000N owner manual Connecting to Video Equipment, When using an S-video cable INPUT3

Page 28

Connecting to Video Equipment

The projector is equipped with input terminals that support component, S-video, and video signals. See the illustration below to connect with the audio-visual equipment.

The image quality is highest in the order of the component signal, the S-video signal and the video signal. If your audio-visual equipment has a component output terminal, use the COMPUTER/ COMPONENT terminal (INPUT1 or INPUT 2) on the projector for video connection.

When using a 3 RCA (Component) to 15-pin D-sub cable (INPUT1 or INPUT2)

To audio output terminal

To component output (Y, CB/PB, CR/PR) terminal

DVD, etc.

	3 RCA
Supplied	(Component)
accessory	to 15-pin
	D-sub cable

To INPUT1

terminalTo AUDIO (INPUT1, 2)

terminal

3 RCA (Component) to 15-pin D-sub cable

ø3.5 mm minijack to RCA audio cable (commercially available)

When using an S-video cable (INPUT3)

To audio output terminal

To S-video output terminal

DVD, etc.

To AUDIO

To INPUT3 (INPUT3, 4)

terminalterminal

L

R

S-video cable

RCA audio cable (com-(commercially available) mercially available)

24

Image 28

Contents EIP-3000N This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified ElectricianIii Page Introduction A. onlyProduct Disposal Using the Menu Screen For Future ReferenceContents Reference Cleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of tem- peratureDo not block the exhaust and intake vents Potential hazard of glass parTemperature monitor function Using the projector in other countriesOther connected equipment Setup Manual Accessories Optional accessoryPart Names and Functions Height 31 AdjustProjector Rear View Output Input 1Audio Input 1 Audio InputBreak Timer Picture ModeUsable Range Inserting the BatteriesAttach the cover and slide it until it clicks into place Quick Start Setup and ProjectionSTANDBY-ON Adjust the projected image with the Setup Guide Upper sideSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupExample Normal Mode Picture Size Projection PRJ Mode120 Stretch Mode Normal ModeScreen Size and Projection Distance Connections Input Terminals and Connectable Main EquipmentSamples of Cables for Connection To audio output terminal To RGB output terminal Connecting to a ComputerComputer To INPUT1 terminal To Audio Terminal Connecting to Video Equipment When using an S-video cable INPUT3Connecting to a Monitor with RGB Input Terminal When using a composite video cable INPUT4Controlling the Projector by a Computer To RS-232C terminalWhen connecting to the LAN terminal using a LAN cable Connecting the Power CordAC socket To AC outlet Turning the Projector On/Off Lamp indicator STANDBY-ON buttonTurning the Projector on Outlet after the cooling fan stops Power indicator STANDBY-ON buttonOn-screen Display confirmation message About the Setup Guide Adjusting the Projected Image Adjusting the FocusAdjusting the Screen Size Image ProjectionAdjusting the Height Use the rear adjustment foot to make the projector levelAdjust lever Make small adjustments Rear adjustment foot HeightAdjusting the Volume Switching the Input ModeAV Mute button Volume buttons Input buttons Press g Keystone to enter Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Press g KeystoneResize Mode Press HresizeVideo Operating with the Remote Control Auto Sync Auto Sync AdjustmentDisplaying and Setting the Break Timer Selecting the Picture ModeInput 1 RGB/INPUT2 RGB Menu ItemsInput 1 Component/INPUT Component/INPUT 3/INPUT Projector adjustment PRJ-ADJ menu Items you can set with the Help menu Help menu nUsing the Menu Screen Menu Selections AdjustmentsPress Q or O and select Picture to adjust Press BmenuTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press hENTER1Selecting the Picture Mode Picture Adjustment Picture menuExample Picture screen menu for Input 3 mode 2Adjusting the Image 3Adjusting the Color Temperature5Lamp Setting ProgressiveAdjusting the Projected Image SCR ADJ menu 1Setting the Resize Mode2Adjusting the Image Position 3Keystone Correction4Setting the On-screen Display 6Selecting the Setup GuideReversing/Inverting Projected Images 5Selecting the Background Image2Auto Sync Auto Sync Adjustment 3Auto Power Off Function4Setting the Confirmation Sound System Sound 5Speaker Setting7Fan Mode Setting 9Checking the Lamp Life Status8System Lock Function Select System Lock, then press hENTER or QLocking the Operation Buttons Enter the same keycode in Re- confirmATaking the Keylock off 1Setting a Password 2DHCP Client Setting 3TCP/IP Setting4Confirming the Projector Information Set the TCP/IP manuallyTroubleshooting with the Help menu Utilizing the Help menu func TionsPress Oor Qto select Help, then MENU/HELPMaintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Lamp Regarding the LampReplacing the Lamp Disconnect the power cord Removing and Installing the Lamp UnitRemove the lamp unit cover Resetting the Lamp Timer Computer Compatibility Chart PC/MACTroubleshooting 23-27Input 1 Component Specifications Product type Projector Model EIP-3000N Video systemDimensions Index Canada Eastern EuropeDeutschland & Österreich Japan & Worldwide