Eiki EIP-3000N owner manual Removing and Installing the Lamp Unit, Disconnect the power cord

Page 60

Regarding the Lamp (Continued)

Removing and Installing the Lamp Unit

Warning!

•Do not remove the lamp unit from the projec- tor right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.

Optional	Lamp unit
accessory	AH-66271

Info

•Make sure that you remove the lamp unit by the handle. Do not touch the glass surface of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

1Press oSTANDBY-ON on the pro- jector or eSTANDBY on the re- mote control to put the projector into standby mode.

•Wait until the cooling fan stops.

2Disconnect the power cord.

•Unplug the power cord from the AC socket.

•Leave the lamp until it has fully cooled down (about 1 hour).

3Remove the lamp unit cover.

•Turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).

STANDBY-ON button

AC socket

1

2

User service screw (for lamp unit cover)

56

Image 60

Contents EIP-3000N This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified ElectricianIii Page Introduction A. onlyProduct Disposal Using the Menu Screen For Future ReferenceContents Reference Cleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of tem- peratureDo not block the exhaust and intake vents Potential hazard of glass parUsing the projector in other countries Temperature monitor functionOther connected equipment Setup Manual Accessories Optional accessoryHeight 31 Adjust Part Names and FunctionsProjector Rear View Output Input 1Audio Input 1 Audio InputBreak Timer Picture ModeInserting the Batteries Usable RangeAttach the cover and slide it until it clicks into place Setup and Projection Quick StartSTANDBY-ON Adjust the projected image with the Setup Guide Upper sideSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupProjection PRJ Mode Example Normal Mode Picture Size120 Normal Mode Stretch ModeScreen Size and Projection Distance Connections Input Terminals and Connectable Main EquipmentSamples of Cables for Connection Connecting to a Computer To audio output terminal To RGB output terminalComputer To INPUT1 terminal To Audio Terminal Connecting to Video Equipment When using an S-video cable INPUT3Connecting to a Monitor with RGB Input Terminal When using a composite video cable INPUT4Controlling the Projector by a Computer To RS-232C terminalConnecting the Power Cord When connecting to the LAN terminal using a LAN cableAC socket To AC outlet Lamp indicator STANDBY-ON button Turning the Projector On/OffTurning the Projector on Power indicator STANDBY-ON button Outlet after the cooling fan stopsOn-screen Display confirmation message About the Setup Guide Adjusting the Projected Image Adjusting the FocusAdjusting the Screen Size Image ProjectionAdjusting the Height Use the rear adjustment foot to make the projector levelAdjust lever Make small adjustments Rear adjustment foot HeightSwitching the Input Mode Adjusting the VolumeAV Mute button Volume buttons Input buttons Press g Keystone to enter Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Press g KeystoneResize Mode Press HresizeVideo Operating with the Remote Control Auto Sync Auto Sync AdjustmentDisplaying and Setting the Break Timer Selecting the Picture ModeMenu Items Input 1 RGB/INPUT2 RGBInput 1 Component/INPUT Component/INPUT 3/INPUT Projector adjustment PRJ-ADJ menu Items you can set with the Help menu Help menu nUsing the Menu Screen Menu Selections AdjustmentsPress Q or O and select Picture to adjust Press BmenuTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press hENTERPicture Adjustment Picture menu 1Selecting the Picture ModeExample Picture screen menu for Input 3 mode 2Adjusting the Image 3Adjusting the Color Temperature5Lamp Setting ProgressiveAdjusting the Projected Image SCR ADJ menu 1Setting the Resize Mode2Adjusting the Image Position 3Keystone Correction4Setting the On-screen Display 6Selecting the Setup GuideReversing/Inverting Projected Images 5Selecting the Background Image2Auto Sync Auto Sync Adjustment 3Auto Power Off Function4Setting the Confirmation Sound System Sound 5Speaker Setting7Fan Mode Setting 9Checking the Lamp Life Status8System Lock Function Select System Lock, then press hENTER or QEnter the same keycode in Re- confirm Locking the Operation ButtonsATaking the Keylock off 1Setting a Password 2DHCP Client Setting 3TCP/IP Setting4Confirming the Projector Information Set the TCP/IP manuallyTroubleshooting with the Help menu Utilizing the Help menu func TionsPress Oor Qto select Help, then MENU/HELPMaintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer Computer Compatibility Chart PC/MACTroubleshooting 23-27Input 1 Component Specifications Product type Projector Model EIP-3000N Video systemDimensions Index Canada Eastern EuropeDeutschland & Österreich Japan & Worldwide