Maintenance Indicators (Continued)
Maintenance indicator | Problem |
| Cause |
| Possible Solution | |||
|
|
|
|
|
| |||
| Normal | Abnormal |
|
|
|
|
| |
|
|
|
|
|
|
|
| |
Tempera- | Off | Red on | The internal | • | Blocked air intake | • Relocate the projector to | ||
ture |
|
| (Standby) | temperature is |
|
|
| an area with proper |
warning |
|
|
| abnormally |
|
|
| ventilation. (see page 8) |
indicator |
|
|
| high. |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| • | Cooling fan | • Take the projector to your | |
|
|
|
|
|
| breakdown |
| nearest EIKI Authorized |
|
|
|
|
| • | Internal circuit |
| Dealer or Service Center |
|
|
|
|
|
| failure |
| (see page 61) for repair. |
|
|
|
|
| • | Clogged air intake |
|
|
|
|
|
|
|
|
|
| |
Lamp | Green on | Red on | The lamp does | • | The lamp is shut | • Disconnect the power cord | ||
indicator | (Green |
| not illuminate. |
| down abnormally. |
| from the AC outlet, and | |
| blinks |
|
|
|
|
| then connect it again. | |
| when the |
|
|
|
|
|
| |
|
| Time to change | • | Remaining lamp life | • Carefully replace the lamp. | |||
| lamp is |
| ||||||
|
| the lamp. |
| becomes 5% or |
| (See page 56.) | ||
| warming |
|
|
| ||||
|
|
|
| less. | • | Take the projector to your | ||
| up or |
|
|
|
| |||
|
|
|
|
|
|
| nearest EIKI Authorized | |
|
| Red on | The lamp does | • |
| |||
| turning |
| ||||||
|
| Dealer or Service Center | ||||||
| (Standby) | not illuminate. | • | Lamp circuit failure |
| |||
| off.) |
| ||||||
|
| (see page 61) for repair. | ||||||
|
|
|
|
|
| |||
|
|
|
|
|
|
| • Please exercise care when | |
|
|
|
|
|
|
|
| replacing the lamp. |
|
|
|
|
|
|
| • | Securely install the cover. |
Power | Green on/ | Green | The power | • | The lamp unit cover | • If the power indicator blinks | ||
indicator | Red on | blinks | indicator blinks |
| is open. |
| in green even when the | |
| Red |
| in green when |
|
|
| lamp unit cover is securely | |
|
| the projector is |
|
|
| installed, contact your | ||
| blinks |
|
|
|
| |||
|
| on. |
|
|
| nearest EIKI Authorized | ||
| (Cooling) |
|
|
|
| |||
|
|
|
|
|
| Dealer or Service Center | ||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| (see page 61) for advice. |
|
|
|
|
|
|
|
|
|
Info
•If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plug- ging in the power cord and turning the power back on. (At least 10 minutes.)
•If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illumi- nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.
•The cooling fan keeps the internal temperature of the projector constant and this function is con- trolled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.
•Do not unplug the power cord after the projector has entered standby mode and while the cooling fan is running. The cooling fan runs for about 90 seconds.
54