Eiki EIP-3000N owner manual Resetting the Lamp Timer

Page 61

4 Remove the lamp unit.

Handle

• Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.

5 Insert the new lamp unit.

•Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.

6 Replace the lamp unit cover.

•Align the tab on the lamp unit cover (1)and place it while pressing the tab (2) to close it. Then tighten the user ser- vice screw to secure the lamp unit cover.

Info

•If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is con- nected to the projector.

Securing screws

2

1

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

•Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or ex- plode.

1Connect the power cord.

•Plug the power cord into the AC socket of the projector.

2Reset the lamp timer.

•While simultaneously holding down rMENU/HELP, pENTER and R on the projector, press oSTANDBY-ON on the projector.

•“LAMP 0000H” is displayed, indicating that the lamp timer is reset.

AC socket

STANDBY-ON button

ENTER button

MENU/HELP button

R button

57

Image 61

Contents EIP-3000N If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedIii Page A. only IntroductionProduct Disposal For Future Reference Using the Menu ScreenContents Reference Accessories CleaningPower Sources Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingAvoid locations with extremes of tem- perature Rest your eyes occasionallyDo not block the exhaust and intake vents Potential hazard of glass parTemperature monitor function Using the projector in other countriesOther connected equipment Setup Manual Optional accessory AccessoriesPart Names and Functions Height 31 AdjustProjector Output Input 1 Rear ViewAudio Input 1 Audio InputPicture Mode Break TimerUsable Range Inserting the BatteriesAttach the cover and slide it until it clicks into place Quick Start Setup and ProjectionSTANDBY-ON Upper side Adjust the projected image with the Setup GuideSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupExample Normal Mode Picture Size Projection PRJ Mode120 Stretch Mode Normal ModeScreen Size and Projection Distance Input Terminals and Connectable Main Equipment ConnectionsSamples of Cables for Connection To audio output terminal To RGB output terminal Connecting to a ComputerComputer To INPUT1 terminal To Audio Terminal When using an S-video cable INPUT3 Connecting to Video EquipmentWhen using a composite video cable INPUT4 Connecting to a Monitor with RGB Input TerminalTo RS-232C terminal Controlling the Projector by a ComputerWhen connecting to the LAN terminal using a LAN cable Connecting the Power CordAC socket To AC outlet Turning the Projector On/Off Lamp indicator STANDBY-ON buttonTurning the Projector on Outlet after the cooling fan stops Power indicator STANDBY-ON buttonOn-screen Display confirmation message Adjusting the Projected Image Adjusting the Focus About the Setup GuideAdjusting the Screen Size Image ProjectionUse the rear adjustment foot to make the projector level Adjusting the HeightAdjust lever Make small adjustments Rear adjustment foot HeightAdjusting the Volume Switching the Input ModeAV Mute button Volume buttons Input buttons Press P/Q or O/R to adjust Keystone Correction Press g Keystone to enter Keystone Correction modeCorrecting Trapezoidal Distortion Press g KeystonePress Hresize Resize ModeVideo Auto Sync Auto Sync Adjustment Operating with the Remote ControlDisplaying and Setting the Break Timer Selecting the Picture ModeInput 1 RGB/INPUT2 RGB Menu ItemsInput 1 Component/INPUT Component/INPUT 3/INPUT Projector adjustment PRJ-ADJ menu Help menu n Items you can set with the Help menuMenu Selections Adjustments Using the Menu ScreenPress Q or O and select Picture to adjust Press BmenuPress P or R and select Bright to adjust To adjust the projected image while watching itPress O or Q to adjust the item selected Press hENTER1Selecting the Picture Mode Picture Adjustment Picture menuExample Picture screen menu for Input 3 mode 3Adjusting the Color Temperature 2Adjusting the Image5Lamp Setting Progressive1Setting the Resize Mode Adjusting the Projected Image SCR ADJ menu2Adjusting the Image Position 3Keystone Correction6Selecting the Setup Guide 4Setting the On-screen DisplayReversing/Inverting Projected Images 5Selecting the Background Image3Auto Power Off Function 2Auto Sync Auto Sync Adjustment4Setting the Confirmation Sound System Sound 5Speaker Setting9Checking the Lamp Life Status 7Fan Mode Setting8System Lock Function Select System Lock, then press hENTER or QLocking the Operation Buttons Enter the same keycode in Re- confirmATaking the Keylock off 1Setting a Password 3TCP/IP Setting 2DHCP Client Setting4Confirming the Projector Information Set the TCP/IP manuallyUtilizing the Help menu func Tions Troubleshooting with the Help menuPress Oor Qto select Help, then MENU/HELPCleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Lamp Regarding the LampReplacing the Lamp Disconnect the power cord Removing and Installing the Lamp UnitRemove the lamp unit cover Resetting the Lamp Timer PC/MAC Computer Compatibility Chart23-27 TroubleshootingInput 1 Component Product type Projector Model EIP-3000N Video system SpecificationsDimensions Index Eastern Europe CanadaDeutschland & Österreich Japan & Worldwide