Eiki EIP-3000N owner manual Adjust the projected image with the Setup Guide, Upper side

Page 21

4.Adjust the projected image with the Setup Guide

1After the projector turns on, the Setup Guide appears. (When “Setup Guide” is set to “On”. n page 45)

2Follow the steps in the Setup Guide and adjust the focus, screen size, and height (angle).

3After adjusting the focus, height (angle) and screen size, press pENTER to finish the Setup Guide.

_P. 30

5.Turn the computer on

6.Select the INPUT mode

Select the “INPUT 1” using the INPUT button on the projector or C INPUT 1 on the remote

control.

On the On the remote On-screen display (RGB) projector control

•When pressing the INPUT button on the projector, input mode switches in the following order: INPUT1INPUT2INPUT3INPUT4

•When using the remote control, press the CINPUT 1/CINPUT 2/DINPUT 3/EINPUT

4 button to switch the INPUT mode.	_P. 32

7. Correct trapezoidal distortion

Correcting trapezoidal distortion using Keystone Correction.

On the projector

Shrinks	Shrinks
upper side.	lower side.

On the remote control

_P. 33

8. Turn the Power off

Press the STANDBY-ON button on the projector or the STANDBY button on the remote control, and then press the button again while the confirmation message is displayed to put the projector into standby mode.

On the	On the remote	On-screen Display
On the	On the remote
projector	control

• Unplug the power cord from the AC outlet after the cooling fan stops.

_P. 29

17

Image 21

Contents EIP-3000N If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedIii Page A. only IntroductionProduct Disposal For Future Reference Using the Menu ScreenContents Reference Accessories CleaningPower Sources Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingAvoid locations with extremes of tem- perature Rest your eyes occasionallyDo not block the exhaust and intake vents Potential hazard of glass parUsing the projector in other countries Temperature monitor functionOther connected equipment Setup Manual Optional accessory AccessoriesHeight 31 Adjust Part Names and FunctionsProjector Output Input 1 Rear ViewAudio Input 1 Audio InputPicture Mode Break TimerInserting the Batteries Usable RangeAttach the cover and slide it until it clicks into place Setup and Projection Quick StartSTANDBY-ON Upper side Adjust the projected image with the Setup GuideSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupProjection PRJ Mode Example Normal Mode Picture Size120 Normal Mode Stretch ModeScreen Size and Projection Distance Input Terminals and Connectable Main Equipment ConnectionsSamples of Cables for Connection Connecting to a Computer To audio output terminal To RGB output terminalComputer To INPUT1 terminal To Audio Terminal When using an S-video cable INPUT3 Connecting to Video EquipmentWhen using a composite video cable INPUT4 Connecting to a Monitor with RGB Input TerminalTo RS-232C terminal Controlling the Projector by a ComputerConnecting the Power Cord When connecting to the LAN terminal using a LAN cableAC socket To AC outlet Lamp indicator STANDBY-ON button Turning the Projector On/OffTurning the Projector on Power indicator STANDBY-ON button Outlet after the cooling fan stopsOn-screen Display confirmation message Adjusting the Projected Image Adjusting the Focus About the Setup GuideAdjusting the Screen Size Image ProjectionUse the rear adjustment foot to make the projector level Adjusting the HeightAdjust lever Make small adjustments Rear adjustment foot HeightSwitching the Input Mode Adjusting the VolumeAV Mute button Volume buttons Input buttons Press P/Q or O/R to adjust Keystone Correction Press g Keystone to enter Keystone Correction modeCorrecting Trapezoidal Distortion Press g KeystonePress Hresize Resize ModeVideo Auto Sync Auto Sync Adjustment Operating with the Remote ControlDisplaying and Setting the Break Timer Selecting the Picture ModeMenu Items Input 1 RGB/INPUT2 RGBInput 1 Component/INPUT Component/INPUT 3/INPUT Projector adjustment PRJ-ADJ menu Help menu n Items you can set with the Help menuMenu Selections Adjustments Using the Menu ScreenPress Q or O and select Picture to adjust Press BmenuPress P or R and select Bright to adjust To adjust the projected image while watching itPress O or Q to adjust the item selected Press hENTERPicture Adjustment Picture menu 1Selecting the Picture ModeExample Picture screen menu for Input 3 mode 3Adjusting the Color Temperature 2Adjusting the Image5Lamp Setting Progressive1Setting the Resize Mode Adjusting the Projected Image SCR ADJ menu2Adjusting the Image Position 3Keystone Correction6Selecting the Setup Guide 4Setting the On-screen DisplayReversing/Inverting Projected Images 5Selecting the Background Image3Auto Power Off Function 2Auto Sync Auto Sync Adjustment4Setting the Confirmation Sound System Sound 5Speaker Setting9Checking the Lamp Life Status 7Fan Mode Setting8System Lock Function Select System Lock, then press hENTER or QEnter the same keycode in Re- confirm Locking the Operation ButtonsATaking the Keylock off 1Setting a Password 3TCP/IP Setting 2DHCP Client Setting4Confirming the Projector Information Set the TCP/IP manuallyUtilizing the Help menu func Tions Troubleshooting with the Help menuPress Oor Qto select Help, then MENU/HELPCleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer PC/MAC Computer Compatibility Chart23-27 TroubleshootingInput 1 Component Product type Projector Model EIP-3000N Video system SpecificationsDimensions Index Eastern Europe CanadaDeutschland & Österreich Japan & Worldwide