Sony MDS-JE530 service manual 15, Slider Cam, BASE UNIT MBU-5D,BD BOARD

Page 15

SLIDER (CAM)

7 slider (Cam)

3bracket (Guide L)

1 two screws (P2.6x6)

4 harnes

4 leaf spring

BASE UNIT (MBU-5D), BD BOARD

5 flexible board (CN104)

6flexible board

(CN101)

7BD board

• Note for Installation of Slider A (Cam)

Set the shaft of Cam gear to be at the position in the figure.

Set the shaft of Lever (O/C) to be at the position in the figure.

5 two screws (P2.6x6)

6 bracket (Guide R)

2base unit (MBU-5D)

1three screws (P2.6 × 6)

3 Remove the solder (Seven portion).

4 screw (M1.7 × 4)

– 15 –

Image 15

Contents MDS-JE530 SPECIFICATIONSSERVICE MANUAL Supplied accessories– 2 – SELF-DIAGNOSISFUNCTIONSelecting the Test Mode Items of Error History Mode Items and ContentsTable of Error Codes – 3 –ELECTRICAL ADJUSTMENTS TABLE OF CONTENTS6.DIAGRAMS DISASSEMBLYADVARSEL Flexible Circuit Board RepairingNotes on chip component replacement – 5 –JIG FOR CHECKING BD BOARD WAVEFORM – 6 –– 7 – Record PrecedureDisplay Precedure – 8 – CHECKS PRIOR TO PARTS REPLACEMENT AND ADJUSTMENTSFig. 1 Reading the Test Mode Display – 9 –RETRY CAUSE DISPLAY MODE Precedure– 10 – Hexadecimal nBinary Conversion TableReading the Display This section is extracted from instruction manual SECTION GENERAL– 11 – LOCATION OF CONTROLSPage FRONT PANEL SECTION SECTION DISASSEMBLY– 13 – CASE– 14 – MAIN BOARDMECHANISM DECK SECTTION MDM-5D – 15 – SLIDER CAMBASE UNIT MBU-5D,BD BOARD SW BOARD, LOADING MOTOR M103 – 16 –– 17 – 1. PRECAUTIONS FOR USE OF TEST MODE2. SETTING THE TEST MODE SECTION TEST MODE5. SELECTING THE TEST MODE – 18 –– 19 – 5-1.Operating the Continuous Playback Mode5-3. Non-VolatileMemory Mode EEP MODE – 20 – 6. FUNCTIONS OF OTHER BUTTONS7. TEST MODE DISPLAYS MEANINGS OF OTHER DISPLAYS – 21 –SECTION ELECTRICAL ADJUSTMENTS 1.PARTS REPLACEMENT AND ADJUSTMENT– 22 – – 23 – 2. PRECAUTIONS FOR CHECKING LASER DIODE EMISSION4. PRECAUTIONS FOR ADJUSTMENTS Laser power meter– 24 – Checking Procedure6-2.Laser Power Check Specification6-4.Focus Bias Check 6-5.C PLAY Checking MO Error Rate CheckCD Error Rate Check – 25 –Setting Procedure 7. INITIAL SETTING OF ADJUSTMENT VALUE9. TEMPERATURE COMPENSATION OFFSET ADJUSTMENT 10. LASER POWER ADJUSTMENTAdjusting Procedure 11. TRAVERSE ADJUSTMENT– 27 – Specification12.FOCUS BIAS ADJUSTMENT – 28 –Adjusting Procedure 13-2.MO Error Rate Check 13.ERROR RATE CHECK15.AUTO GAIN CONTROL OUTPUT LEVEL ADJUSTMENT 13-1.CD Error Rate Check– BD BOARDSide B – Adjustment Location– 30 – – BD BOARDSide A –– 32 – MDS-JE530 SECTION DIAGRAMS6-1.BLOCK DIAGRAM – MD SERVO Section – – 31 –– 34 – 6-2.BLOCK DIAGRAM – MAIN Section –MDS-JE530 – 33 –– 35 – Note on Printed Wiring BoardNote on Schematic Diagram • Circuit Boards Location – 36 –•Semiconductor Location 6-4.PRINTED WIRING BOARD – BD Board –– 38 – •See page 36 for Circuit Boards Location– 39 – – 40 –MDS-JE530 MDS-JE530 6-6.SCHEMATIC DIAGRAM – BD Board 2/2 – See•– 41 – – 42 –– 44 – 6-7.SCHEMATIC DIAGRAM – SW Board –6-8.PRINTED WIRING BOARD – SW Board – – 43 –page 36 for Circuit Boards Location 6-9.PRINTED WIRING BOARD – MAIN Board – See•– 45 – – 46 –Page Page 41 Page – 47 –– 48 – MDS-JE530– 49 – – 50 –MDS-JE530 • Semiconductor Location – 51 –– 52 – MDS-JE530Page 47 Page – 53 –– 54 – MDS-JE530IC101 •IC Block Diagrams – BD Board –– 55 – – 56 –IC431 – 57 –IC310 M5293L6-14.IC PIN FUNCTION DESCRIPTION – 58 –•BD BOARD IC121 CXD2656R – 59 –– 60 – – 61 – •MAIN BOARD IC501 M30624MG-207FPSYSTEM CONTROLLER – 62 –– 63 – – 64 – SECTION EXPLODED VIEWS – 65 –1CHASSIS SECTION 59 54 52 2FRONT PANEL SECTION 61 64 61 63 6166 61 61 51 53223 207 – 67 –3MECHANISM SECTION MDM-5D 213 207 202 201254 253 – 68 –4BASE UNIT SECTION MBU-5D 252 263 270– 69 – SECTION ELECTRICAL PARTS LIST– 70 – DISPLAYKEY SW – 71 –DISPLAY MAIN – 72 –KEY SW MAIN – 73 –MAIN – 74 –POWER SW – 75 –MAIN 9-928-824-11 MDS-JE530– 76 – Sony Corporation

Related manuals

Manual 160 pages 14.46 Kb