Philips DCR 2021 user manual Safety instructions, For future reference

Page 6

Safety instructions

Your receiver is powered using an AC adaptor.This equipment has been

 

manufactured to meet the appropriate safety standards, but the instructions

 

below must be followed to operate it safely.These instructions must be kept

EN

for future reference.

 

-Before connecting the AC adaptor to the mains, check that the mains supply voltage corresponds to the voltage printed on it. If the mains voltage is different, consult your dealer.

-The AC adaptor has been designed for indoor use only.

-The receiver and AC adaptor do not contain any user-serviceable parts. Do not attempt to open them. All maintenance work must be carried out by qualified personnel.

-Periodically inspect the AC adaptor for damage. Do not use if damage is found. Refer to qualified personnel.

-Unplug the AC adaptor from the mains during lightning storms.

-To prevent fire or shock hazard, do not expose this equipment to rain or moisture.

-The receiver should be placed on a firm surface, and the ventilation openings must not be covered with items, such as newspapers, table clothes, curtains, etc.

-Do not install this equipment near any heat sources such as radiators, stoves or other apparatus that produce heat. Protect it from direct sunlight.

-When installing the receiver, ensure there is a gap of approximately 2 cm around it to enable air to circulate freely and prevent overheating.

-Leave access to the AC adaptor in case emergency shutdown is required.

-Do not place any combustible objects on the receiver (candles, etc.).

-No objects filled with liquids, such as vases, shall be placed on the receiver. It shall not be exposed to dripping or splashing. Should this happen, disconnect the AC adaptor from the mains and consult qualified personnel.

-Make sure that children do not place any foreign objects in any of the openings.

-For cleaning, use a soft, damp (not wet) cloth. Never use any abrasive cloth and aerosol cleaners.

Your receiver, as any electronic equipment, consumes power. In order to reduce power consumption, please switch your receiver to standby or “Low Power” whenever you are not using it.

For maximum energy saving we recommend you switch off the receiver by unplugging it from the mains if you are not using it for a long time.

53

Image 6
Contents Benutzerhandbuch Foreword Dear CustomerQuick installation Press OK to start scanning for channels Meaning of symbols Safety instructions For future referenceContents Advanced settings Timer ManagerSettings Restoring factory settingsProduct description Front panelRear panel Inserting your Smart Card Insert the smartcard with the golden chip facing upRemote control RED, GREEN,YELLOW BlueConnecting your Digital-receiver Connecting to a TV and VCR both fitted with Scart socketsConnecting to your audio equipment analogue or digital Analogue Connection aConnecting of a video projector to watch digital TV Channel scan First installationFirst installation settings Set your TV display formatSearch failure Before starting a new scanDay-to-day operation Using Low Power modeYour cable receiver is in standby mode Digital radioUsing channel lists Using number keysUsing P+/P- keys PIN codeTo modify your PIN code, refer to paragraph PIN-Code Change Volume control / +Banner To close the banner, press Info a third timeCurrent programme options While watching digital TV or listening to digital radioSetting a timer via the Timer Manager Recording timersSet a timer from the EPG Deleting an active timerSwitching to analogue TV Premiere features Premiere MultifeedMenu Tree Menu treeMenu navigation Changing settingsCancelling/storing changes BasicsSmartcard Premiere Service MenuPIN-Code Change SystemDisplay Dolby DigitalWake-up channel To delete an existing timer Setting your receiverTimer Manager To set a new timer or edit an existing timerChannel Manager List OrganizationMonday to Friday , or Monday to Saturday Scroll to the channel you want to move using the ty keys List EditingChannel List Main TV, which is the only editable list Settings Channel PoolDisplay options Must not be used as a password To enable Parental LockTo modify your receiver password For ParentsSystem Settings Advanced settingsTV Settings Enter your new password again to confirm Press ExitYou can also access this screen via the Premiere menu Time SettingsFactory settings Decoder StatusChannel Search Your receiver later, and then press OK to confirmSoon as you set your receiver to standby Changing the remote control configuration Other settingsRestoring factory settings 11.3 VCR/DVD Recorder ControlEXT Digital-Receiver and VCR or DVD settings Recording with the VCR/DVD Recorder Control featurePage Troubleshooting Problem Possible cause ActionChange the TV Scart Output Technical specifications Video decoding3111 176