Denon Comprehensive Guide to the AVR 2802 Manual for Enhanced Sound Experience

Page 24

ENGLISH

When you adjust the channel levels while in the SYSTEM SETUP CHANNEL LEVEL mode, the channel level adjustments made will affect ALL surround modes. Consider this mode a Master Channel Level adjustment mode.

After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the individual surround modes and adjust channel levels that will be remembered for each of those modes. Then, whenever you activate a particular surround sound mode, your preferred channel level adjustments for just that mode will be recalled. Check the instructions for adjusting channel levels within each surround mode on Page 42.

You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, 5CH/6CH STEREO, DOLBY/DTS SURROUND, ROCK ARENA, JAZZ CLUB, VIDEO GAME, MONO MOVIE, and MATRIX.

Setting the digital in assignment

•This setting assigns the digital input jacks of the AVR-2802/982 for the different input sources.

1	At the System Setup Menu select “Digital In Assignment”.

2	Switch to the Digital In Assignment screen.
	Switch to the Digital In Assignment screen.
	ENTER

	3	Select the digital input jack to be assigned to the input source.
	3	• To select the input source
		• To select the input source

•To select the digital input jack

Select “OFF” for input sources for which no digital input jacks are used.

If “Yes” is selected for “Default”, the settings are automatically reset to the default values.

4		Enter the setting.
		Enter the setting.
	ENTER	The System Setup Menu reappears.
		The System Setup Menu reappears.

NOTES:

•The OPTICAL 3 jacks on the AVR-2802/982’s rear panel are equipped with an optical digital output jack for recording digital signals on a CD recorder, MD recorder or other digital recorder. Use this for digital recording between a digital audio source (stereo - 2 channel) and a digital audio recorder.

•Do not connect the output of the component connected to the OPTICAL 3 OUT jack on the AVR-2802/982’s rear panel to any jack other than the OPTICAL 3 IN jack.

•“PHONO” and “TUNER” cannot be selected on the Digital In Assignment screen.

24

Image 24

Contents AVR-2802/982 English Francais Safety Instructions Table of Contents Before UsingFeatures Connecting the audio components ConnectionsConnecting video components Connecting a video component equipped with S-Video jacks Precaution when using S-jacksConnecting the video decks Connecting a DVD player DVD in jacks Connecting a monitor TV Monitor OUT jackConnecting the antenna terminals AM loop antenna assemblyAn F-type FM antenna cable plug can be connected directly Connection of AM antennasConnecting the external input EXT. in jacks Connecting the Multi Zone jacksConnecting banana plugs Speaker system connectionsConnection the speaker terminals Precautions when connecting speakers EnglisPart Names and Functions Front PanelRemote control unit System Call buttonsSetting UP the System System Setup buttonEnter button Cursor buttonsBefore setting up the system Setting the type of speakersDisplay the System Setup Menu Press the Enter button to finalize the setting Frequency mode is sent to the subwooferNone…… Select this when no speakers are installed ParametersSetting the Crossover Frequency and Subwoofer mode Assignment of low frequency signal rangeSubwoofer mode Crossover FrequencySetting Setting the delay time PreparationsSetting the channel level Select Test Tone ModeSelect the mode Adjust the levelVolume Select Auto or ManualSetting the digital in assignment To select the input sourceSetting the on-screen display OSD Auto tuner presetsAfter completing system setup On-screen display signalsRemote Control Unit Using the remote control unitInserting the batteries Set mode switch 2 to the position for the component to be Be operated with this remote controlOperating Denon audio components OperatedPreset memory Audio component Preset memory Video componentCombinations of Personal System Codes DVD VDP Operating a video component stored in the preset memory VDP, VCR or TVOperate the video component DVD player system buttonsLearning function Using the system call function System call functionSystem call buttons Storing signals Clearing system call settingsClearing learned remote control signals OperationBefore operating To select the input source when REC Input mode selection functionPlaying the input source Select the input source to be playedDigital PCM mode Digital DTS modeAnalog mode Input signal displayPlayback using the external input EXT. in jacks Adjusting the sound quality toneAfter starting playback Listening over headphones Turning the sound off temporarily mutingChecking the currently playing program source, etc Playing one source while recording another REC OUT mode Multi-source recording/playbackMulti-zone playback with multi-source Surround Before playing with the surround functionSelect the Dolby Surround Pro Logic II mode Dolby Pro Logic indicator lightsFader function Surround parameters q Pro Logic II Mode Dimension ControlPanorama Control Center Width ControlSet the input mode to Auto or DTS Select the Dolby/DTS Surround modeDolby Digital indicator lights When playing Dolby Digital sourcesSelect the various parameters Adjust the parameter settings MenuDialogue Normalization Surround modes and their features DSP Surround SimulationPersonal Memory Plus DSP surround simulation Set the parametersWhen turned clockwise When turned counterclockwisePress the Surround Parameter button Tone control setting Cinema MusicSurround modes and parameters Auto tuning Manual tuningListening to the Radio Preset memory Checking the preset stationsRecalling preset stations Last Function MemoryInitialization of the Microprocessor Troubleshooting Types of multi-channel signals Additional InformationTypes of sources Movie audio Movie theater sound fieldSurround back speakers Number of surround back speakersSpeaker setting examples When not using surround back speakersSurround Dolby Surround Dolby Digital Dolby Surround AC-3Dolby Digital and Dolby Pro Logic Dolby Digital compatible media and playback methodsDTS Digital Surround DTS compatible media and playback methodsDTS-ESTMDiscrete DTS-ESTMMatrixDTS Neo6TM surround DTS Neo6 CinemaDVD TV/DBS Surround modes and parameters Specifications 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan Page Page Page First name in digital audio Speaker Configuration Delay Time Digital In Assignment