Denon AVR-2802/982 Listening over headphones, Turning the sound off temporarily muting

Page 39

ENGLIS

[2] Listening over headphones

1

Connect the headphones to the

NOTE:

PHONES jack of the front panel.

PHONES

 

To prevent hearing loss, do not raise the volume level excessively

when using headphones.

1

B

2

Press the SPEAKER A or B to turn the

 

 

 

 

speaker off.

 

 

• The output to the speaker and pre-out

 

 

jacks is turned off and no sound is

2

 

produced from the speakers.

 

(Main unit)

[3] Turning the sound off temporarily (muting)

1

Use this to turn off the audio output

 

 

temporarily.

 

Press the MUTING button.

 

Cancelling MUTING mode.

Press the MUTING button again.

MUTING

(Remote control unit)

 

DOLBY / DTS

 

SPEAKER

SURROUND

DIRECT

DSP SIMULATION

5CH / 6CH STEREO

STEREO

 

 

MASTER VOL.

INPUT MODE

ANALOG

EXT.IN

AUDIO

 

TAPE

CDR/MD

 

 

CD

MULTI

MUTING

AVR/AVC

VIDEO

DVD

TV

 

 

 

VDP

VCR

 

1

[4] Combining the currently playing sound with the desired image

1

Simulcast playback

VIDEO SELECT

Use this switch to monitor a video

 

source other than the audio source. Press the VIDEO SELECT button repeatedly until the desired source

B

appears on the display. Cancelling simulcast playback.

(Main unit)

Select “SOURCE” using the video select button.

Switch the program source to the component connected to the video input.

[5]Checking the currently playing program source, etc.

1

1

On screen display

 

 

• Each time an operation is performed,

 

a description of that operation

 

appears on the display connected to

 

the unit’s VIDEO MONITOR OUT

 

jack. Also, the unit’s operating status

 

can be checked during playback by

 

pressing the remote control unit’s ON

 

SCREEN button.

 

Such information as the position of

 

the input selector and the surround

 

parameter settings is output in

 

sequence.

ON SCREEN

RETURN

(Remote control unit)

 

SYSTEM

SURROUND

 

TUNING

SETUP

PARAMETER

 

BAND

TITLE

MENU/GUIDE

 

 

 

 

 

 

CH SELECT

 

MODE

 

ENTER

 

 

 

 

 

 

SELECT

1

MEMORY

STATUS

ON SCREEN

 

DISPLAY

RETURN

USE/LEARN T.TONE

MULTI

DVD

1

 

 

SET UP

1

Using the dimmer function

• Use this to change the brightness of the display.

DIMMER

Front panel display

Descriptions of the unit’s operations are also displayed on the front panel display. In addition, the display can be switched to check the unit’s operating status while playing a source by pressing the STATUS button.

STATUS

STATUS

DISPLAY

(Main unit)

(Remote control unit)

The display brightness changes in four steps

(bright, medium, dim and off) by pressing the

remote control unit’s DIMMER button repeatedly.

The brightness changes in 3 steps each time the button is pressed, and finally the display turns off.

(Main unit)

39

Image 39
Contents AVR-2802/982 English Francais Safety Instructions Before Using Table of ContentsFeatures Connections Connecting the audio componentsConnecting video components Connecting a video component equipped with S-Video jacks Precaution when using S-jacksConnecting the video decks Connecting a monitor TV Monitor OUT jack Connecting a DVD player DVD in jacksConnection of AM antennas Connecting the antenna terminalsAM loop antenna assembly An F-type FM antenna cable plug can be connected directlyConnecting the Multi Zone jacks Connecting the external input EXT. in jacksConnecting banana plugs Speaker system connectionsConnection the speaker terminals Englis Precautions when connecting speakersFront Panel Part Names and FunctionsSystem Call buttons Remote control unitCursor buttons Setting UP the SystemSystem Setup button Enter buttonBefore setting up the system Setting the type of speakersDisplay the System Setup Menu Parameters Press the Enter button to finalize the settingFrequency mode is sent to the subwoofer None…… Select this when no speakers are installedCrossover Frequency Setting the Crossover Frequency and Subwoofer modeAssignment of low frequency signal range Subwoofer modeSetting Preparations Setting the delay timeSelect Test Tone Mode Setting the channel levelSelect Auto or Manual Select the modeAdjust the level VolumeTo select the input source Setting the digital in assignmentAuto tuner presets Setting the on-screen display OSDOn-screen display signals After completing system setupRemote Control Unit Using the remote control unitInserting the batteries Operated Set mode switch 2 to the position for the component to beBe operated with this remote control Operating Denon audio componentsPreset memory Audio component Preset memory Video componentCombinations of Personal System Codes DVD VDP DVD player system buttons Operating a video component stored in the preset memoryVDP, VCR or TV Operate the video componentLearning function Using the system call function System call functionSystem call buttons Clearing system call settings Storing signalsClearing learned remote control signals OperationBefore operating Select the input source to be played To select the input source when RECInput mode selection function Playing the input sourceInput signal display Digital PCM modeDigital DTS mode Analog modePlayback using the external input EXT. in jacks Adjusting the sound quality toneAfter starting playback Listening over headphones Turning the sound off temporarily mutingChecking the currently playing program source, etc Multi-source recording/playback Playing one source while recording another REC OUT modeMulti-zone playback with multi-source Before playing with the surround function SurroundSelect the Dolby Surround Pro Logic II mode Dolby Pro Logic indicator lightsFader function Center Width Control Surround parameters q Pro Logic II ModeDimension Control Panorama ControlWhen playing Dolby Digital sources Set the input mode to Auto or DTSSelect the Dolby/DTS Surround mode Dolby Digital indicator lightsSelect the various parameters Adjust the parameter settings MenuDialogue Normalization Surround modes and their features DSP Surround SimulationPersonal Memory Plus Set the parameters DSP surround simulationWhen turned clockwise When turned counterclockwisePress the Surround Parameter button Tone control setting Music CinemaSurround modes and parameters Auto tuning Manual tuningListening to the Radio Checking the preset stations Preset memoryRecalling preset stations Last Function MemoryInitialization of the Microprocessor Troubleshooting Movie theater sound field Types of multi-channel signalsAdditional Information Types of sources Movie audioNumber of surround back speakers Surround back speakersWhen not using surround back speakers Speaker setting examplesDolby Digital compatible media and playback methods SurroundDolby Surround Dolby Digital Dolby Surround AC-3 Dolby Digital and Dolby Pro LogicDTS compatible media and playback methods DTS Digital SurroundDTS Neo6 Cinema DTS-ESTMDiscreteDTS-ESTMMatrix DTS Neo6TM surroundDVD TV/DBS Surround modes and parameters Specifications 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan Page Page Page First name in digital audio Speaker Configuration Delay Time Digital In Assignment