Denon AVR-2802/982 Example Stereo, Digital PCM mode, Digital DTS mode, Analog mode

Page 37

ENGLIS

Select the play mode.

3 Press the SURROUND MODE button, then turn the SELECT knob.

Example: Stereo

SURROUND	SELECT
MODE	STEREO

(Main unit)

(Remote control unit)

To select the surround mode while adjusting the surround parameters, channel volume or tone control, press the surround mode button then operate the selector.

SURROUND

MODE

		(Main unit)
4	Start playback on the selected component.
4	• For operating instructions, refer to the component’s
	manual.
5	Adjust the volume.	MASTER VOLUME
			MASTER VOL.
	The volume level is	(Main unit)	(Remote control unit)
	displayed on the master
	volume level display.

The volume can be adjusted within the range of –70 to 0 to 18 dB,

Input mode display

•In the AUTO mode

INPUT

AUTO PCMDTS

•In the DIGITAL PCM mode

INPUT

AUTO PCMDTS

•In the DIGITAL DTS mode

INPUT

AUTO PCMDTS

•In the ANALOG mode

INPUT

AUTO PCMDTS

Input signal display

•DOLBY DIGITAL

SIGNAL

DIGITAL

•DTS

SIGNAL

DIGITAL

•PCM

SIGNAL

DIGITAL

One of these lights, depending on the input signal.

DIGITAL ANALOG

DIGITAL

DIGITAL

ANALOG

in steps of 1 dB. However, when the channel level is set as described on page 22 or pages 42 and 43, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. (In this case the maximum volume adjustment range is “18 dB — (Maximum value of channel level)”.)

Input mode when playing DTS sources

•Noise will be output if DTS-compatible CDs or LDs are played in the “ANALOG” or “PCM” mode.

When playing DTS-compatible sources, be sure to connect the source component to the digital input jacks (OPTICAL/COAXIAL) and set the input mode to “DTS”.

The DIGITAL indicator lights when digital signals are being input properly. If the DIGITAL indicator does not light, check whether the digital input component setup (page 24) and connections are correct and whether the component’s power is turned on.

NOTE:

•The DIGITAL indicator will light when playing CD-ROMs containing data other than audio signals, but no sound will be heard.

37

Image 37

Contents AVR-2802/982 English Francais Safety Instructions Before Using Table of ContentsFeatures Connections Connecting the audio componentsConnecting video components Precaution when using S-jacks Connecting a video component equipped with S-Video jacksConnecting the video decks Connecting a monitor TV Monitor OUT jack Connecting a DVD player DVD in jacksAM loop antenna assembly Connecting the antenna terminalsAn F-type FM antenna cable plug can be connected directly Connection of AM antennasConnecting the Multi Zone jacks Connecting the external input EXT. in jacksSpeaker system connections Connecting banana plugsConnection the speaker terminals Englis Precautions when connecting speakersFront Panel Part Names and FunctionsSystem Call buttons Remote control unitSystem Setup button Setting UP the SystemEnter button Cursor buttonsSetting the type of speakers Before setting up the systemDisplay the System Setup Menu Frequency mode is sent to the subwoofer Press the Enter button to finalize the settingNone…… Select this when no speakers are installed ParametersAssignment of low frequency signal range Setting the Crossover Frequency and Subwoofer modeSubwoofer mode Crossover FrequencySetting Preparations Setting the delay timeSelect Test Tone Mode Setting the channel levelAdjust the level Select the modeVolume Select Auto or ManualTo select the input source Setting the digital in assignmentAuto tuner presets Setting the on-screen display OSDOn-screen display signals After completing system setupUsing the remote control unit Remote Control UnitInserting the batteries Be operated with this remote control Set mode switch 2 to the position for the component to beOperating Denon audio components OperatedPreset memory Video component Preset memory Audio componentCombinations of Personal System Codes DVD VDP VDP, VCR or TV Operating a video component stored in the preset memoryOperate the video component DVD player system buttonsLearning function System call function Using the system call functionSystem call buttons Clearing system call settings Storing signalsOperation Clearing learned remote control signalsBefore operating Input mode selection function To select the input source when RECPlaying the input source Select the input source to be playedDigital DTS mode Digital PCM modeAnalog mode Input signal displayAdjusting the sound quality tone Playback using the external input EXT. in jacksAfter starting playback Turning the sound off temporarily muting Listening over headphonesChecking the currently playing program source, etc Multi-source recording/playback Playing one source while recording another REC OUT modeMulti-zone playback with multi-source Before playing with the surround function SurroundDolby Pro Logic indicator lights Select the Dolby Surround Pro Logic II modeFader function Dimension Control Surround parameters q Pro Logic II ModePanorama Control Center Width ControlSelect the Dolby/DTS Surround mode Set the input mode to Auto or DTSDolby Digital indicator lights When playing Dolby Digital sourcesMenu Select the various parameters Adjust the parameter settingsDialogue Normalization DSP Surround Simulation Surround modes and their featuresPersonal Memory Plus Set the parameters DSP surround simulationWhen turned counterclockwise When turned clockwisePress the Surround Parameter button Tone control setting Music CinemaSurround modes and parameters Manual tuning Auto tuningListening to the Radio Checking the preset stations Preset memoryLast Function Memory Recalling preset stationsInitialization of the Microprocessor Troubleshooting Additional Information Types of multi-channel signalsTypes of sources Movie audio Movie theater sound fieldNumber of surround back speakers Surround back speakersWhen not using surround back speakers Speaker setting examplesDolby Surround Dolby Digital Dolby Surround AC-3 SurroundDolby Digital and Dolby Pro Logic Dolby Digital compatible media and playback methodsDTS compatible media and playback methods DTS Digital SurroundDTS-ESTMMatrix DTS-ESTMDiscreteDTS Neo6TM surround DTS Neo6 CinemaDVD TV/DBS Surround modes and parameters Specifications 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan Page Page Page First name in digital audio Speaker Configuration Delay Time Digital In Assignment