Denon AVR-2802/982 operating instructions Table of Contents, Before Using

Page 4

ENGLISH

2INTRODUCTION

Thank you for choosing the DENON AVR-2802/982 Digital Surround A / V receiver. This remarkable component has been engineered to provide superb surround sound listening with AV theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favorite music sources.

As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the contents of this manual before proceeding.

TABLE OF CONTENTS

z Before Using ……………………………………………………………………4

. Operation …………………………………………………………………35~41

x Cautions on Installation

………………………………………………………4

⁄0Surround ……………………………………………………………………42~46

c Cautions on Handling

…………………………………………………………5

⁄1DSP Surround Simulation…………………………………………………47~52

v Features …………………………………………………………………………5

⁄2Listening to the Radio

…………………………………………………53~55

b Connections …………………………………………………………………6~13

⁄3Last Function Memory

………………………………………………………55

n Part Names and Functions ………………………………………………14, 15

⁄4Initialization of the Microprocessor …………………………………………55

m Setting up the system ……………………………………………………16~26

⁄5Troubleshooting…………………………………………………………………56

, Remote Control Unit ………………………………………………………27~35

⁄6Additional Information ……………………………………………………57~64

 

 

⁄7Specifications …………………………………………………………………65

2ACCESSORIES

Check that the following parts are included in addition to the main unit:

q Operating instructions…..1

w Warranty ( for North America model only )………...........1 e Service station list…….....1

r Remote control unit

t R6P/AA batteries….....….2

y AM loop antenna…...............1 u FM indoor antenna…1

(RC-903)............…......1

r t y u

1 BEFORE USING

Pay attention to the following before using this unit:

•Moving the set

To prevent short circuits or damaged wires in the connection cords, always unplug the power cord and disconnect the connection cords between all other audio components when moving the set.

•Before turning the power switch on

Check once again that all connections are proper and that there are not problems with the connection cords. Always set the power switch to the standby position before connecting and disconnecting connection cords.

•Store this instructions in a safe place.

After reading, store this instructions along with the warranty in a safe place.

•Note that the illustrations in this instructions may differ from the actual set for explanation purposes.

2 CAUTIONS ON INSTALLATION

Noise or disturbance of the picture may be generated if this unit or any other electronic equipment using microprocessors is used near a tuner or TV.

If this happens, take the following steps:

•Install this unit as far as possible from the tuner or TV.

•Set the antenna wires from the tuner or TV away from this unit’s power cord and input/output connection cords.

•Noise or disturbance tends to occur particularly when using indoor antennas or 300 Ω /ohms feeder wires. We recommend using outdoor antennas and 75 Ω /ohms coaxial cables.

For heat dispersal, leave at least 10 cm of space between the top, back and sides of this unit and the wall or other components.

4 inch/10 cm or more

B

4 inch/10 cm or more

Wall

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents AVR-2802/982 English Francais Safety Instructions Table of Contents Before UsingFeatures Connecting the audio components ConnectionsConnecting video components Precaution when using S-jacks Connecting a video component equipped with S-Video jacksConnecting the video decks Connecting a DVD player DVD in jacks Connecting a monitor TV Monitor OUT jackConnecting the antenna terminals AM loop antenna assemblyAn F-type FM antenna cable plug can be connected directly Connection of AM antennasConnecting the external input EXT. in jacks Connecting the Multi Zone jacksSpeaker system connections Connecting banana plugsConnection the speaker terminals Precautions when connecting speakers EnglisPart Names and Functions Front PanelRemote control unit System Call buttonsSetting UP the System System Setup buttonEnter button Cursor buttonsSetting the type of speakers Before setting up the systemDisplay the System Setup Menu Press the Enter button to finalize the setting Frequency mode is sent to the subwooferNone…… Select this when no speakers are installed ParametersSetting the Crossover Frequency and Subwoofer mode Assignment of low frequency signal rangeSubwoofer mode Crossover FrequencySetting Setting the delay time PreparationsSetting the channel level Select Test Tone ModeSelect the mode Adjust the levelVolume Select Auto or ManualSetting the digital in assignment To select the input sourceSetting the on-screen display OSD Auto tuner presetsAfter completing system setup On-screen display signalsUsing the remote control unit Remote Control UnitInserting the batteries Set mode switch 2 to the position for the component to be Be operated with this remote controlOperating Denon audio components OperatedPreset memory Video component Preset memory Audio componentCombinations of Personal System Codes DVD VDP Operating a video component stored in the preset memory VDP, VCR or TVOperate the video component DVD player system buttonsLearning function System call function Using the system call functionSystem call buttons Storing signals Clearing system call settingsOperation Clearing learned remote control signalsBefore operating To select the input source when REC Input mode selection functionPlaying the input source Select the input source to be playedDigital PCM mode Digital DTS modeAnalog mode Input signal displayAdjusting the sound quality tone Playback using the external input EXT. in jacksAfter starting playback Turning the sound off temporarily muting Listening over headphonesChecking the currently playing program source, etc Playing one source while recording another REC OUT mode Multi-source recording/playbackMulti-zone playback with multi-source Surround Before playing with the surround functionDolby Pro Logic indicator lights Select the Dolby Surround Pro Logic II modeFader function Surround parameters q Pro Logic II Mode Dimension ControlPanorama Control Center Width ControlSet the input mode to Auto or DTS Select the Dolby/DTS Surround modeDolby Digital indicator lights When playing Dolby Digital sourcesMenu Select the various parameters Adjust the parameter settingsDialogue Normalization DSP Surround Simulation Surround modes and their featuresPersonal Memory Plus DSP surround simulation Set the parametersWhen turned counterclockwise When turned clockwisePress the Surround Parameter button Tone control setting Cinema MusicSurround modes and parameters Manual tuning Auto tuningListening to the Radio Preset memory Checking the preset stationsLast Function Memory Recalling preset stationsInitialization of the Microprocessor Troubleshooting Types of multi-channel signals Additional InformationTypes of sources Movie audio Movie theater sound fieldSurround back speakers Number of surround back speakersSpeaker setting examples When not using surround back speakersSurround Dolby Surround Dolby Digital Dolby Surround AC-3Dolby Digital and Dolby Pro Logic Dolby Digital compatible media and playback methodsDTS Digital Surround DTS compatible media and playback methodsDTS-ESTMDiscrete DTS-ESTMMatrixDTS Neo6TM surround DTS Neo6 CinemaDVD TV/DBS Surround modes and parameters Specifications 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan Page Page Page First name in digital audio Speaker Configuration Delay Time Digital In Assignment
Top Page Image Contents